Abstract:Atomization of low-temperature fuel is encountered in extreme operating conditions of liquid propulsion systems such as cold start and high-altitude relight for aeroengines. Fuel temperature has a great impact on airblast spray characteristics by influencing fuel viscosity and thus the gas–liquid interaction, which raises the demand to clarify the temperature-dependent transition in near-nozzle breakup behavior and the corresponding droplet size distribution. A liquid-centered swirl coaxial injector is tested on the low-temperature swirl spray and combustion test rig at Zhejiang University, using 25 kHz high-speed digital off-axis holography. RP-3 aviation kerosene is atomized under ignition conditions at temperatures of 233, 253, and 301 K, fuel pressures of 0.03 and 0.69 MPa, and air pressure ranging from 0 to 4.0 kPa. Time-resolved near-nozzle dynamics suggest four types of elementary breakup processes: wavy-sheet breakup, pulsating breakup, membrane-type breakup, and nonaxisymmetric Rayleigh breakup. Each process alternately dominates the near field as fuel Reynolds number (Ref) and aerodynamic Weber number (Weg) decrease, corresponding to four primary breakup modes. A mode classification plot is summarized. Spray structures show an extended breakup length and reduced spray cone angle as fuel temperature (Tf) decreases. Increasing air pressure (Pg) promotes spray expansion at 0.03 MPa, but contracts spray cone at 0.69 MPa. Cross-sectional Sauter mean diameter (SMD) distribution indicates a solid-cone spray at 0.03 MPa and a hollow cone spray at 0.69 MPa. Lowering Tf will rise the SMD in the spray center at 0.03 MPa and transform the toroidal SMD distribution at 0.69 MPa into a solid one. Finally, a temperature-related SMD model is derived considering the exponential viscosity–temperature relationship, and a good fit with R2 > 0.95 is achieved. This research aims to deepen the understanding of the effects of low temperature on the transition of near-nozzle atomization characteristics for airblast sprays. Both spray visualization and SMD results provide reference for numerical simulations and near-nozzle spray modeling.

Microscopic Characterization of Isooctane Spray in the Near Field under Flash Boiling Condition

Experimental Characterization of Closely Coupled Split Isooctane Sprays under Flash Boiling Conditions

Microscopic investigation of near-field spray characteristics of 2-methylfuran, ethanol and isooctane under flash boiling conditions

The Influence of Flash Boiling Conditions on Spray Characteristics with Closely Coupled Split Injection Strategy

Comparison of Spray Collapses at Elevated Ambient Pressure and Flash Boiling Conditions Using Multi-Hole Gasoline Direct Injector

Experimental study of the macroscopic characteristics of methanol low-pressure injection spray

Macroscopic Spray Characteristics of Iso-Octane, Ethanol, Gasoline and Methanol from a Multi-Hole Injector under Flash Boiling Conditions

Spray Morphology Transformation of Propane, N-Hexane and Iso-Octane under Flash-Boiling Conditions

Effect of Flash Boiling on Microscopic and Macroscopic Spray Characteristics in Optical Gdi Engine

Numerical study on spray collapse process of ECN spray G injector under flash boiling conditions

Effects of Low Temperature on Near-Nozzle Breakup and Droplet Size Distribution in Airblast Kerosene Spray

Microscopic and Macroscopic Characterization of Spray Impingement under Flash Boiling Conditions with the Application of Split Injection Strategy

General Understanding on Spray Collapse Process of an Asymmetrical Multi-Hole Direct Injection Gasoline Injector under Wide Flash-Boiling Conditions

Near-field spray atomization characteristics at the end of injection under flash-boiling and non-flash-boiling conditions

Microscopic Level Study on the Spray Impingement Process and Characteristics

Microscopic Study on the Mechanisms for Formation of the Initial Spray Morphology

Characterizing Under-Expansion Behaviors Induced by Rapid Phase Change of Flash-Boiling Jets

INSIGHT INTO JET-TO-JET INTERACTIONS UNDER FLASH-BOILING CONDITIONS USING A MULTI-HOLE INJECTOR WITH WIDE ENVELOP SPRAY ANGLE

A morphological study of supercritical fuel flash-boiling spray

Experimental Study on Microscopic and Macroscopic Characteristics of Diesel Spray with Split Injection

Investigation into Shock-to-shock Interactions Induced by Flash Boiling and the Impact on Spray Behaviors