Abstract:The electron beam orbit stability is very important for the Free Electron Laser (FEL) facility. The high beam position stability requirement results in the high position stability for the FEL key components, such as quadruple magnet (Q) and beam position monitor (BPM). This work focus on the research of the dynamic performance of a mechanical support system composed of mechanical supports including sheets and adjustments and a granite block mounted on them. It will be applied for the beam based alignment (BBA) Q magnet and BPM for the Soft X-ray FEL project (SXFEL). The Finite-element FE calculations of the model characteristics were carried out to guide the subsequent tests. The test results show that the support system can meet the requirement of the SXFEL project. INTRDUCTION Shanghai Soft X-ray FEL (SXFEL) and the Dalian Coherent Light Source project (DCLS) are significant national science and technology infrastructure. The electron beam stability is one of the most important factors that influence the properties of FEL. The increasing demands of beam position stability result in the higher position stability requirement for the FEL key parts such as undulator and quadruple magnet. Since the mechanical support system for the FEL provides supporting, location and position adjustment, the high mechanical stability of the supports is indirectly expected. Soft X-ray Free Electron Laser (FEL) light in the SCSS project developed a new support-stand composed of cordierite body with low thermal expansion rate attached with two flanges at top and bottom used in undulator line [1]. Sand-filled insulated steel support pedestals were used in undulator line of LCLS (Linac Coherent Light Source) [2]. Swiss FEL also developed a new mechanical support with low thermal expansion for BBA [3]. For the DCLS&SXFEL projects, granite blocks with produced from Shandong Province of China have been used as the main component of the support for BBA. In this work, several kinds of mounting method between granite block with mechanical components and Ground were designed and discussed. The first eigenfrequency is an important index for the stability and performance of supports [4].This paper describes an attempt to understand and increase the first eigenfrequency of different kinds of support for BBA to improve its stability, which based on the fact that the ground vibrations at the SXFEL(SSRF site) are larger than at other light sources [5]. This paper presents two different kinds of support prototype for Beam Based Alignment (BBA). Modal hammering experiments and FE analysis of prototypes are discussed in this work. Finally, vibration measurement result about the final support for BBA mounting in the tunnel is shown in this paper.

HEPS pre-collimation unit BQ magnet precision high stability pad lock position adjustment device design

A Compact and High-Precision Method for Active Beam Stabilization System

Design of quadrupole and sextupole magnets supporting mechanism for HLS storage ring and vibration tests of the prototype

High-precision Spatial Measurement Method of Accelerator Pre-Alignment Based on Multiple Total Stations

Modeling And Controller Design Of A Novel Large-Gap Magnetic Suspension And Balance System For 3d Non-Contact Manipulation

The Design and Application of Magnetic Landmark used for Magnetic Fiducialization of HEPS Insertion Devices

High-Precision Spatial Measurement Method of Accelerator Cell Pre-alignment Based on Multiple Total Stations

Dynamic performance of a support system for bba com- ponents in sxfel

Performance Analysis of a New Adjustable Superconducting Magnet Suspension System

Study on Support for HALF Beam Position Monitor Displacement Measurement System

Design of the Integral Field Measurement System of Dipole Magnets

Design of Automatic Mooring Chain Magnetic Powder Testing Device

Study on Finite Element Simulation and Experiment Based on the Design of Zero-Point Clamping System

Design and Testing of a Compliant ZTTΘ Positional Adjustment System with Hybrid Amplification

Design of Control for Beam Based Alignment System at HLS

Design and Analysis of Mechanical Structure for On-Board HTS Magnets Subjected to High Acceleration

Design and Analysis on KTX Reversed Field Pinch Device Main Support Structure

Closed-orbit Distortion Study of XiPAF Upgrading Project Synchrotron

Optimized Design Method Study for Cavity BPM System

Design and Construction of a Multi-Sensor Position Monitoring System Applied to Key Components of Synchrotron Sources

A robust smoothing analysis strategy for improving particle accelerator alignment and installation accuracy and efficiency based on HALF design