Abstract:A mechanistic kinetic rate theory model originally developed for the prediction of fission gas behavior in oxide nuclear fuels under steady-state and transient conditions has been assessed to investigate its applicability to model fission gas behavior in U-Pu-Zr metallic alloy fuel. In order to capture and validate the underlying physics for irradiated U-Pu-Zr fuels, the mechanistic model was applied to evaluate fission gas release, fission gas and fission product induced swelling, and detailed gas bubble size distributions in three different fuel zones: the outer alpha-U, the intermediate, and the inner gamma-U zones.Due to its special microstructural features, the alpha-U zone in U-Pu-Zr fuels is believed to contribute the largest fraction of fission gas release among the different fuel zones. It is shown that with the use of small effective grain sizes, the mechanistic model can predict fission gas release that is in reasonable consistence with (though slightly lower than) experimentally measured data. These simulation results are comparable to the experimentally measured fission gas release since the mechanism of fission gas transport through the densely distributed laminar porosity in the alpha-U zone is analogous to the mechanism of fission gas transport through the interconnected gas bubble porosity utilized in the mechanistic model.Detailed gas bubble size distributions predicted with the mechanistic model in both the intermediate zone and the high temperature gamma-U zone of U-Pu-Zr fuel are also compared to experimental measurements from available SEM micrographs. These comparisons show good agreement between the simulation results and experimental measurements, and therefore provide crucial guidelines for the selection of key physical parameters required for modeling these two zones. Material properties such as fuel grain size and thermal diffusivity of gas and model parameters such as di-atom nucleation probability and gas bubble re-solution constant are predicted by these comparisons. In addition, the results of parametric studies for several parameters are presented for both the intermediate zone and the gamma-U zone simulations in order to clarify the sensitivities of simulation results on these parameters. Published by Elsevier B.V.

A Model for Zinc Addition Effect on Corrosion Product Release, Activation and Transportation in RCS Based on Mixed-conduction Model and Its Application

Research on the effects of corrosion resistant zinc injection in primary circuit of large-scale PWR plants on core crud amount

A Corrosion Cracking Mechanism-Based Model with Molten Salt Corrosion Damage Coupling the Effect of Chloride Impurity and Plastic Deformation

Three-phase Modelling of Electrochemical Chloride Removal from Corroded Steel-Reinforced Concrete

A Self-Balanced Electrochemical Model for Corrosion of Reinforcing Steel Bar in Considering the Micro-Environments in Concrete

Development of an oxidation model for the prediction of the corrosion risk induced by deposits on cladding surface in PWRs

A corrosion model for CZ cladding based on in-pile irradiation data

Dynamic Self-Balanced Electrochemical Model for Non-Uniform Corrosion of Steel Reinforcement in Concrete under Combined Effects of Heat-Moisture-chlorine-oxygen

Development of oxygen/corrosion product mass transfer model and oxidation-corrosion model in the lead-alloy cooled reactor core

Constriction Percolation Model for Coupled Diffusion-Reaction Corrosion of Zirconium in PWR

Numerical Simulation of Zircaloy-Water Reaction Based on the Moving Particle Semi-Implicit Method and Combined Analysis with the MIDAC Code for the Nuclear-Reactor Core Melting Process

Some Fundamental Understandings of Zn-injection Water Chemistry on Material Corrosion in Pressurized Water Reactor Primary Circuit

An Initial Assessment of a Mechanistic Model, GRASS-SST, in U–Pu–Zr Metallic Alloy Fuel Fission-Gas Behavior Simulations

A Coupled Electro-Chemo-Mechanical Model for the Stress Corrosion Cracking Prediction of Stainless Steel in High-Temperature Water

Integrated Model Development for Safeguarding Pyroprocessing Facility: Part II – Case Studies and Model Integration

Research on the Influence of Chemical Reaction Model over MCCI Heat Transfer Process

Improved cellular automata modeling of corrosion/oxidation mechanism of stainless steel in LBE

Role of zirconium conversion coating in corrosion performance of aluminum alloys: An integrated first-principles and multiphysics modeling approach

Thermodynamic and kinetic modeling of Mn-Ni-Si precipitates in low-Cu reactor pressure vessel steels

A Study of the Impact of Cladding Materials on SCMR Neutronics Parameters

Integrated Modeling of Second Phase Precipitation in Cold-Worked 316 Stainless Steels under Irradiation