Improved Design of TSC Arc-Suppression Reactor and Its Automatic Control System

赵志丽,杨学昌,常思哲

DOI: https://doi.org/10.3969/j.issn.1001-8425.2004.07.002

2004-01-01

Abstract:The present situation and problems of the arc-suppression reactor are summarized. The structure, principle and design of the improved TSC arc-suppression reactor are presented briefly.

What problem does this paper attempt to address?

Improved Design of Automatic Tuning Arc Suppression Coil with Thyristor Series Capacitors

赵志丽,杨学昌,常思哲

DOI: https://doi.org/10.3969/j.issn.1001-1609.2004.05.007

2004-01-01

Abstract:After analyzing the current state and existing problems of automatic resonance arc suppression coil, the improved novel arc suppression coil with thyristor series capacitors is proposed. This paper introduces its structure, principle and design method in detail. This apparatus features higher response speed, better waveform, higher reliability characteristics, etc. The online measure of shunt capacitive current is more accurate and convenient.
Discussion on Some Problems of the Intelligent Low-Voltage Reactive Power Compensation System

朱连欢,邱海锋,周浩

DOI: https://doi.org/10.3969/j.issn.1001-4551.2009.05.030

2009-01-01

Abstract:In order to improve the real-time performance and stability of the existing TSC system compensation,the existing TSC dynamic reactive power compensation system was analyzed and discussed.The related algorithms and techniques of TSC were discussed from five aspects of the reactive power algorithm,the compensation principle,the control strategy,the structure of the main circuit,etc..The selection basis was given by comparing the advantages and disadvantages of various methods.And the TSC system development process that needs attention was described in detail.The research results show that the reasonable algorithms and techniques can improve the performance of the TSC effectively.
Novel Adjustable TSC Arc Suppressing Coil

曹振翀,杨学昌,吴振升

DOI: https://doi.org/10.3969/j.issn.1001-1609.2004.04.007

2004-01-01

Abstract:With the wide use of arc suppressing coil,the traditional type can not satisfy the development of power system.This paper introduces a new type of continuously adjustable TSC arc suppressing coil,illuminates its principle,and compares its advantages and disadvantages with other types.
Design Scheme on Distributed Control System of HTR-10

马涛,魏利强,张良驹,陈晓明

2009-01-01

Abstract:The distributed control system(DCS) of 10 MW High-Temperature Gas-cooled Reactor(HTR-10) takes charge of operation monitoring and control to HTR-10.The disadvantages of the original DCS at present such as reliability of facilities and history operation data system were introduced.Based on the requirements of technologic systems and control objects,the system architecture,functions and performances were analyzed.The I/O channels configuration was completed.The design scheme which was comprised of the multi-redundancy hardware flat based on Schnieder Quantum 67160 series products,the system software flat by UNITY and the configuration tool by iFIX were presented.The control rods and fuel handling control systems were driven by PTO modules.The AC sampling scheme was modified by adopting intelligent instrument.A specified logical gateway for third-party communication will be developed.The design scheme present in this article can solve the problems and match the demands from DCS of HTR-10.
Study on Reactivity Control Strategies for the Thermoelectric Integrated Space Nuclear Reactor

Jian Li,Qin Zhou,Yan Xia,Jian Mou,Ruiqiong Zhai,Zicai Shen,Boying Lin

DOI: https://doi.org/10.1016/j.anucene.2020.107607

IF: 1.9

2020-01-01

Annals of Nuclear Energy

Abstract:The Autonomous Circulation Miniature Integrated nuclear Reactor (ACMIR) has features of compact structure, high power density and high efficiency. The reactivity control strategy is an important aspect in the design of ACMIR, which is essential for reactor safe operation. In this paper, two ex-core reactivity control options, namely, the rotating control drums and sliding reflector segments, were investigated. Furthermore, an optimization design was conducted on both strategies, including alternative absorber materials, thickness of absorber, absorber angle and the thickness of reflector. Finally, we analyzed and compared the neutronic characteristics with different control schemes, including the reactivity insertion behavior, reactivity temperature coefficient, submersion criticality and spatial power distribution. This work helps to improve the safety characteristics of ACMIR in reactivity control and operation. (C) 2020 Elsevier Ltd. All rights reserved.
Design Scheme of Special Safety System for Supercritical-Water-Cooled Reactor

Hai-ming SUI,Jian-qiang SHAN,Xue-kong HUANG,Jun-li GOU,Hong YANG

DOI: https://doi.org/10.3969/j.issn.0258-0926.2013.01.015

2013-01-01

Abstract:This paper gives a brief description of the design requirement and design principle of Supercritical-Water-Cooled Reactor (SCWR) Nuclear Power Plant safety system, particularly describes the function and the system design scheme of the automatic depressing system (ADS), high pressure feedwater tank (RMT), passive residual heat removal system (ICS), passive containment cooling system (PCCS) and gravity driving core cooling system (GDCS). The operation of the safety system is analyzed after loss of feedwater flowrate accident, to verify the validity of the SCWR safety system described above.
Research on the Key Design of Emergency Core Cooling Scheme for Tsinghua High Flux Reactor

Zhuang Wang,Meng Lv,Heng Xie

DOI: https://doi.org/10.1016/j.anucene.2024.110898

IF: 1.9

2025-01-01

Annals of Nuclear Energy

Abstract:This paper introduces the updated emergency core cooling scheme for Tsinghua High Flux Reactor. The corresponding Relap5 model is established and key designs are studied by simulating the corresponding loss-of-coolant accidents. These key designs specifically involve ACC internal pressure, ACC coolant temperature, ACC liquid fraction, ACC location, emergency pumps, check valves at pressure vessel inlets, the design of pressure vessel outlet, connection between the dry pool and the reactor pool, and operation pressure. Through analysis, some general conclusions are obtained, which can be used to guide the design of emergency core cooling system in the near future. Critical heat flux is predicted by Sudo correlations during loss-of-coolant accidents. According to minimum departure from nucleate boiling ratio, core safety margin is evaluated. By studying these key designs, the current scheme can be better understood and more safety margins can be found.
IMPROVEMENTS ON CONTROL SYSTEM PERFORMANCE OF A SMALL PRESSURIZED WATER REACTOR

Huasong Cao,Peiwei Sun,Wei Wang,Sufang Xin

DOI: https://doi.org/10.1299/jsmeicone.2019.27.1567

2019-01-01

Abstract:Traditional control system with fixed gains may encounter problems such as large overshoot and large settling time. Large overshoot of the control rod position shortens the lifetime of control rod. Thus, improvements on traditional control system performance to decrease overshoot is necessary. A small pressurized water reactor model with a thermal power of 150MW is established by RELAP5. The model includes reactor core, pressurizer, two U-tube steam generators (SG) and main coolant pumps. Based on PID method, the reactor power control system, pressurizer pressure and level control system, and feedwater flow control system are designed. The parameters of the control system are tuned. The performance of control systems are tested by introducing step and ramp changes in load. The overshoot and settling time are evaluated. Due to large overshoot of control rod, fuzzy controller is adopted to improve performance of control systems. Through the introduction of typical load patterns, the performance of the optimized control system is compared with the traditional control system. Overshoot and settling time of the control rod position are decreased. Performance has been significantly improved by introducing fuzzy control.
ALL-COEFFICIENT ADAPTIVE CONTROL SYSTEM DESIGN FOR A SPACE NUCLEAR REACTOR

Qian Ma,Zhitong Yu,Peiwei Sun,Yuwen Jia,Shifa Wu

DOI: https://doi.org/10.1115/icone28-64459

2021-01-01

Abstract:Topaz-II is a space nuclear reactor developed by the Former Soviet Union. It is a thermal-neutron reactor with UO2 ceramics as fuel. Electricity is generated based on the principle of thermoelectric conversion. The reactivity is controlled by several groups control drums. Its lifetime can be three years and its reactivity feedback and further dynamic characteristics are varying with its lifetime. The positive reactivity feedback characteristics and different dynamic characteristics in different lifetime make it changeling to design a suitable control system for Topaz-II. All-coefficient adaptive control is a single-input singleoutput adaptive control method applied to a parameter unknown, linear time invariant or slowly varying object. In some specific conditions, it is also suitable for the non-linear systems. In this method, the model where the sum of coefficients is equal to one is reconstructed based on the original dynamic model. All coefficients in this model can be identified. Therefore, it is possible to realize the optimal control. Firstly, the model of Topaz-II nuclear reactor system is built. It includes point-reactor kinetics model with six groups delayed neutrons, a one-dimensional lumped transient thermal model of the nuclear fuel element and the moderator, a thermionic model of the converters, a control drum drive model. The reactivity feedbacks with fuel temperature and moderator are considered. Based on the model, the dynamic characteristics are analyzed. Then, with the nonlinear model of Topaz-II nuclear reactor system, the transfer functions are obtained and analyzed. Based on the transfer functions, the model where the sum of coefficients is equal to one is built by using the all-coefficient adaptive control method. After dealing with the parameter and analyzing the error, the all-coefficient adaptive control systems are designed. To evaluate the performance of the control systems, power maneuvering events including a 30%FP (Full Power) step change and a reactivity disturbance of 0.0065 are simulated. The responses with traditional and proposed control methods are evaluated and compared. The simulation results show that the all-coefficient adaptive control system has a better performance in settling time and overshoot compared with those with traditional PID controller.
Development and Realization of a Novel Measurement and Control Method for Automatic Compensation Arc-Suppression Equipment

Jing Yan,Zhiyang Ma

DOI: https://doi.org/10.1049/cp:20061816

2006-01-01

Abstract:The technological core of automatic compensation arc-suppression equipments lies in the accurate tracing and measuring of system capacitive current to earth. In view of the limitation in present testing methods of capacitive current, a novel measuring and controlling method, which takes the impact of system damping rate into consideration, is proposed and then the method for two extinction coils operating in parallel is obtained. Based on this method, a controller for automatic compensation arc-suppression equipment is developed centering on PC 104 industrial controlling computer. Simulation tests shows that the method proposed in this paper can effectively improve the measuring precision of system capacitive current to earth. (6 pages)
Design and submersion criticality safety analysis of a space gas-cooled reactor with an in-core reactivity control structure doped with spectral shift absorbers

Zhiqi Chen,Jiejin Cai,Xuezhong Li

DOI: https://doi.org/10.1016/j.anucene.2024.111020

IF: 1.9

2024-11-07

Annals of Nuclear Energy

Abstract:The neutron spectrum of space gas-cooled reactors will be thermalized in the submerged accident, which increases the reactivity and even reaches supercritical, indicating that space gas-cooled reactors should remain sufficiently subcritical in the submerged accident. In this paper, an in-core reactivity control structure named control ring for a space gas-cooled reactor is presented, and nine nuclides that have significantly higher absorption cross-section to thermal neutrons than fast neutrons (also known as spectral shift absorbers, SSAs) are considered to be doped into the control structure for the submersion criticality safety. The reactivity of the variation of the geometry parameter of the control ring and the SSAs atom density is calculated both in the normal case and the submerged accident case, and a comparison with the reactivity without the control ring is also calculated to evaluate the control effect of the control ring. The result shows that the control ring doped with SSAs can reduce the reactivity in the submerged accident significantly, and 10 B, 149 Sm, 151 Eu, 155 Gd have better performance in the submerged accident. The reactivity of two-component composite SSAs made up from the four SSAs that have better performance are also calculated, the result shows that the composite SSAs have a better performance than the single SSA. The neutron spectrum and the burnup of the reactor are calculated to analyze the control effect of the control ring and verify whether the result can meet the requirement of the reactor design. These results can provide a reference for the design of space gas-cooled nuclear reactors.

nuclear science & technology
Study on Reactivity Control Method for Supercritical Water-Cooled Reactor CSR1000

Bang-yang XIA,Ping YANG,Lian-jie WANG,Qing LI,Xiang LI

DOI: https://doi.org/10.3969/j.issn.0258-0926.2013.01.006

2013-01-01

Abstract:The reactivity control of SCWR depends completely upon the burnable poisons and control rod clusters,so the burnable poisons placement and control rods strategy are very important for SCWR core design.In this paper,the burnable poison Er2O3 is chosen to homogeneously mix in the UO2pellets of all fuel rods,and the cross-plate control rods similar to that of BWRs are used.By the three-dimensional neutronics and thermal-hydraulic coupled calculations method,the control rods programming has been determined.In addition,the equilibrium core for CSR1000 has also been established by the three-dimensional equilibrium core search,and then an analysis of its key parameters shows that it can entirely satisfy the general design and safety requirements.
Compensation Characteristics of Arc Suppressing Coil Controlled by TCR

CHEN Heng,CAI Xu,WANG Jun

DOI: https://doi.org/10.3321/j.issn:1000-1026.2007.11.018

2007-01-01

Abstract:The phase-controlled arc-suppressing coil is a type of adjustable arc-suppressing coil controlled by TCR(Thyristor Controlled Reactor),being capable of the large adjustable range of current and the continuously adjusted compensation current.In this paper,the working characteristics of arc-suppressing coil controlled by TCR are demonstrated and the correctness of theoretical analysis is proved by the related simulation with ATP(Alternative Transient Process)and experiments on the simulated 10 kV power distribution network.It is indicated that the distortion ratio of harmonic currents can be controlled within the finite range by the filtering circuit,which,however,slowers the response speed of the circuit and produces the cross-zero disorder.The correspondent controlling strategy has been designed through an analysis of some key problems in controlling,greatly improving the compensation effect and operating safety.
Thermal Hydraulic Design and Analysis of Thorium-based Advanced CANDU Reactor (TACR)

Shiying Wei,Chenglong Wang,Wenxi Tian,Suizheng Qiu,G. H. Su

DOI: https://doi.org/10.1016/j.nucengdes.2017.07.036

IF: 1.7

2017-01-01

Nuclear Engineering and Design

Abstract:The application of thorium fuel in advanced CANDU (CANadian Deuterium Uranium) reactors is an economic solution to sustainable development of nuclear energy. In this paper, the thermal hydraulic design and transient analysis of Thorium-based Advanced CANDU Reactor (TACR) heat transport system are conducted using self-programmed code CANTHAC (CANDU Thermal Hydraulic Analysis Code). In the code CANTHAC, the single channel model and the point kinetics model are adopted to simulate the core thermal hydraulic and neutronic behaviors. A distributed parameter model is adopted in the simulation of integral economizer U-tube steam generator (IEUTSG). Multi-region non-equilibrium model is applied to simulate the pressurizer. The characteristics of heat transport pumps were simulated by four-quadrant analogy curves. The code is verified with ACR-700 steady-state analysis. The calculation results agreed well with ACR-700 design values and the relative errors are all within 2%. With CANTHAC steady-state module, the preliminary thermal hydraulic design of TACR is conducted. A 1000 MW double loop reactor with 520 fuel channels is designed. Single loop mass flow rate was designed to be 3202 kg/s. Under the design scheme, the maximum cladding temperature and the maximum temperature are 340.2 degrees C and 1369.9 degrees C, which satisfied the design requirements. The transient analysis of TACR heat transport system was performed with CANTHAC transient module. SG feed water temperature reduction accident, and complete loss of Class IV accident were conducted. In the SG feed water temperature reduction accident, a new balance of neutron and thermal hydraulic is reached and the core power increases by 5% at last. In the complete loss of Class IV accident, the maximum fuel temperature reaches peak value at 1172 degrees C and still has some safety margin. The ROH (Reactor Outlet Header) pressure does not exceed 105% of the design value, which meet the safety criterion demand.
Thermohydraulic and safety analysis on China advanced research reactor under station blackout accident

Wenxi Tian,Suizheng Qiu,Guanghui Su,Dounan Jia,Xingmin Liu,Jianwei Zhang

DOI: https://doi.org/10.1016/j.anucene.2007.01.010

IF: 1.9

2007-01-01

Annals of Nuclear Energy

Abstract:A thermohydraulic and safety analysis code-TSACC has been developed using Fortran90 language to evaluate the transient thermohydraulic behavior of the China advanced research reactor (CARR) under station blackout accident (SBA). For the development of TSACC, a series of corresponding mathematical and physical models were applied. Point reactor neutron kinetics model was adopted for solving the reactor power. All possible flow and heat transfer conditions under station blackout accident were considered and the optional correlations were supplied. The usual finite difference method was abandoned and the integral technique was adopted to evaluate the temperature field of the plate type fuel elements. A new simple and convenient equation was proposed for the resolution of the transient behaviors of the main pump instead of the complicated four-quadrant model. Gear method and Adams method were adopted alternately for a better solution to the stiff differential equations describing the dynamic behavior of the CARR. The computational result of TSACC showed the adequacy of the safety margin of CARR under SBA. For the purpose of Verification and Validation (V&V), the simulated results of TSACC were compared with those of RELAP5/MOD3 and a good agreement was obtained. The adoption of modular programming techniques enables TASCC to be applied to other reactors by easily modifying the corresponding function modules.
Optimization of a Fuel Assembly for Supercritical Water-Cooled Reactor CSR1000

Fawen Zhu,Lele Zheng,Quan-Yao Ren,Ti Yue,Hua Pang,Linna Feng,Xiang Li,Renjie Ran,Shan Huang

DOI: https://doi.org/10.3389/fenrg.2021.678741

IF: 3.4

2021-06-22

Frontiers in Energy Research

Abstract:As one of the Generation IV nuclear reactors, the SCWR (supercritical water-cooled reactor) has high economy and safety margin, good mechanical properties for its high thermal efficiency, and simplified structure design. As the key component of nuclear reactor, the fuel assembly has always been the main issue for the design of the SCWR. The design of the fuel assembly for CSR1000 proposed by the Nuclear Power Institute of China (NPIC) has been optimized and presented in this study, which is composed of four subassemblies welded by four filler strips and guide thimbles arranged close together in the cross-shaped passage. Aiming at improving the hydraulic buffer performance of the cruciform control rod, the scram time and terminal velocity of control rod assembly were calculated to assess the scram performance based on the computational fluid dynamics and dynamic mesh method, and the mechanical property and neutronic performance of assemblies were also investigated. It has been demonstrated that the optimized fuel assembly had good feasibility and performance, which was a promising design for CSR1000.

energy & fuels
Probability Safety Analysis of Improvement Design of ASG System

SHAO Ge,TONG Lili,CAO Xuewu,XUE Junfeng,WU Qifang,WANG Yong,YAN Yingdi

DOI: https://doi.org/10.3981/j.issn.1000-7857.2012.h1.002

2012-01-01

Abstract:The principal role of the Auxiliary Feedwater System(ASG) is to support the removal of stored and decayed heat from the Reactor Coolant System (RCS). After the Three Mile Island (TMI) accident, the ASG modification for the mitigation of the accidents of the nuclear power plants (NPPs) becomes a research issue. In order to improve the overall safety of nuclear power plants (NPP) and the system reliability, the ASG is renovated with the improved safety facility (ESF) for the Fuqing NPP. A fault tree (FT) model of the ASG before/after the improvement is built by the Probabilistic Safety Analysis (PSA) to analyze the system reliability. The β factor model is used to quantitatively analyze the failures of the components and the minimal cutsets of the FT are calculated. The results show that the probability of the ASGP0200 and the ASGP0300 as the top key event is significantly reduced; and the percentage of the turbine driven pump minimal cutset probability in the top key event probability is also significantly reduced. The initial event tree (ET) model related to the ASG before/after the improvement is built to analyze the contribution of the improvement on the CDF under the power operation condition. The percentage of the initial event contribution on the CDF before/after the ASG improvement is also investigated. The results show that because of the ASG design improvements, the CDF of the NPP is decreased, which means that the safety of the NPP is improved.
Research on Reactive Power Compensator of High Voltage TSC

刘卫星,高强,徐殿国

2010-01-01

Abstract:For the existing reactive power compensation technology,some new control methods are proposed,and a measuring high-voltage TSC var compensation device is designed.The device is based on the chip of TMS320F2812,and the reactive power of system is considered as the main control objective.To obtain the actual switching condition of capacitors,capacitor switching feedback mechanism is introduced.Capacitor duty cycle-scan mode is realized,which ensures all equivalent capacitors running in turn.For the high-voltage main circuit,multi-output high-voltage isolated current source is used as the thyristor triggering circuit,which can guarantee high isolation level and excellent triggering synchronization.
Design of Passive Heat-Switch Between Pressure Tube and Calandria Tube Based on the Principle of Metal Expand on Heating and Contract on Cooling of TACR

XU Liang-wang,JIA Bao-shan,YU Ji-yang

DOI: https://doi.org/10.3969/j.issn.0258-0926.2006.01.015

2006-01-01

Abstract:The paper presents a design of passive heat-switch between pressure tube and calandria tube of Thorium-based Advanced CANDU Reactor(TACR).The heat switch is designed on the principle of heated metal expanding and contract on cooling.The valve driven by a metal stick controls the type of heat conductor between pressure tube and calandria tube.The design meets the requirement of high heat transfer resistance in normal operation and low heat transfer resistance to remove the residual heat in accident.The design is reliable and effective.

Improved Design of TSC Arc-Suppression Reactor and Its Automatic Control System

Improved Design of Automatic Tuning Arc Suppression Coil with Thyristor Series Capacitors

Discussion on Some Problems of the Intelligent Low-Voltage Reactive Power Compensation System

Novel Adjustable TSC Arc Suppressing Coil

Design Scheme on Distributed Control System of HTR-10

Study on Reactivity Control Strategies for the Thermoelectric Integrated Space Nuclear Reactor

Design Scheme of Special Safety System for Supercritical-Water-Cooled Reactor

Research on the Key Design of Emergency Core Cooling Scheme for Tsinghua High Flux Reactor

IMPROVEMENTS ON CONTROL SYSTEM PERFORMANCE OF A SMALL PRESSURIZED WATER REACTOR

ALL-COEFFICIENT ADAPTIVE CONTROL SYSTEM DESIGN FOR A SPACE NUCLEAR REACTOR

Development and Realization of a Novel Measurement and Control Method for Automatic Compensation Arc-Suppression Equipment

Design and submersion criticality safety analysis of a space gas-cooled reactor with an in-core reactivity control structure doped with spectral shift absorbers

Study on Reactivity Control Method for Supercritical Water-Cooled Reactor CSR1000

Compensation Characteristics of Arc Suppressing Coil Controlled by TCR

Thermal Hydraulic Design and Analysis of Thorium-based Advanced CANDU Reactor (TACR)

Thermohydraulic and safety analysis on China advanced research reactor under station blackout accident

Optimization of a Fuel Assembly for Supercritical Water-Cooled Reactor CSR1000

Probability Safety Analysis of Improvement Design of ASG System

Research on Reactive Power Compensator of High Voltage TSC

Design of Passive Heat-Switch Between Pressure Tube and Calandria Tube Based on the Principle of Metal Expand on Heating and Contract on Cooling of TACR