Abstract:The ignition control system is the critical Electromagnetic interference source in automobile, and the transient voltage in primary circuit loop attacks the accumulator and interferes with the ECU or other electronic devices by power cord, and simultaneously the high frequency spark noise caused by spark plug may produce radiated noise which affects the electromagnetic environment inside and outside the automobile. Lots of vehicle manufactory are faced with the problem that the EMI testing value exceeds the threshold value. It is an urgent need to research the ignition system electromagnetic compatibility and seek the ignition system EMI suppressing method for enhancing the vehicle EMC. The objective of this study is to analyze the ignition system EMI formation mechanism and its effect for electromagnetism environment inside the vehicle, then taking effective suppressing measures to optimize ignition system EMC design. This paper simulates the ignition primary circuit transient current and voltage in EMC simulating software by analysing the working principle of gasoline engine ignition system and the formation mechanism of ignition system EMI. This study establishes secondary coil circuit loop spark plug discharge modle, the high voltage wire is equivalent to antenna, the electric field EMI distribution inside vehicle has been worked out, and then it researched the electromagnetic environmental effect of high-voltage wire position, length, working frequency and load impedance. The radiated electric field distribution is acquired by establishing vehicle body, antenna model in the Simulation Analysis. The longer length the high-voltage wire is, the stronger the radiated noise is. The height of wire from ground has little effect on electric field intensity, working frequency is higher and the radiated noise is stronger. These studies provide judgement basis for the optimization of electronic equipment installation position. This paper analyses the reason of ignition system EMI and electromagnetic environmental effect, and gives suggestion for susceptive electronic equipment installation. An important limitation of the current study is our study can’t include all ignition system problems, and some problems need to be discussed further; more convenient vehicle body modeling methods and spark plug noise suppressing methods need to be researched further. It is a new study of analysing ignition system EMI, establishing math model and analysing the effect of susceptivity equipment for electromagnetic environment. At present, most of car manufactories mainly focus on electromagnetic noise testing, so the simulating researching of ignition system disturbance characteristic can improve automobile overall EMC design. The research result indicates: making use of damp high-voltage wire, resistance type spark plug and shielding method for ignition coil and high-voltage wire can reduce radialization disturbance, but sometimes various suppressing measures will be taken.

Simulating and Analyzing the Electromagnetism Noise Disturbing in the System of Washing Machine

Investigation of Noise Characteristics of Electric Vibrator Utilizing Acoustic Camera and Transfer Path Analysis

Vibration and Noise Optimization of Variable-Frequency-Driven SPMSM Used in Compressor Based on Electromagnetic Analysis and Modal Characteristics

Modeling and Suppression of Electromagnetic Interference Noise on Motor Resolver of Electric Vehicle

Numerical and experimental analysis on the vibration and radiated noise of the cylinder washing machine

Electromagnetic Noise Analysis of the PMSM Motor Caused by Carrier Frequency of the Inverter

A Study on EMI Noise Countermeasure Design of a Dishwasher

The Influence of Vibration and Acoustic Noise of Axial Flux Permanent Magnet Machines by Inverter

Effect of Common-Mode Interference on Communication Performance of a Motor Drive System

Influence of PWM Current Harmonics on Electromagnetic Noise of External-Rotor In-Wheel Permanent Magnet Synchronous Motor for Electric Vehicle

A Systematic Design and Optimization Technique for the Suppression of EMI Common Mode (CM) Noise

Analysis of Air Gap Magnetic Field and Noise Suppression of Permanent Magnet Synchronous Machine with Fractional Slot

Three-Dimensional Field Calculation and Analysis of Electromagnetic Vibration and Noise for Disk Permanent Magnet Synchronous Machines

Electromagnetic Noise Analysis and Optimization for Permanent Magnet Synchronous Motor Used on Electric Vehicles

High-frequency modeling based EMC performance improvement of power supplies in inverters

Simulation Analysis of Electromagnetic Compatibility in Vehicle Ignition Control System

Electromagnetic Compatibility Design for the Measurement and Control System of the Test Table

Electromagnetic noise analysis of servomotor used in secondary water supply equipment

Analysis of EMI in Motor System Driven by PWM Inverter

Simulation Analysis of Electromagnetic Noise From Squirrel-cage Asynchronous Motors