Abstract:The buckling mechanics of fibre-reinforced shape-memory polymer composites (SMPCs) under finite flexure deformation is investigated. The analytical expressions of the key parameters during the buckling deformation of the materials were determined, and the local post-buckling mechanics of the unidirectional fibre-reinforced SMPC were further discussed. The cross section of SMPC under flexural deformation can be divided into three areas: the non-buckling stretching area, non-buckling compression area and buckling compression area. These areas were described by three variables: the critical buckling position, the neutral plane position and the fibre buckling half-wavelength. A strain energy expression of the SMPC thermodynamic system is developed. According to the principle of minimum energy, the analytical expressions of key parameters in the flexural deformation process is determined, including the critical buckling curvature, critical buckling position, position of the neutral plane, wavelength of the buckling fibre, amplitude of the buckling fibre and macroscopic structural strain of the composite material. The results showed that fibre buckling occurred in the material when the curvature increasing from infinitesimal to the critical value. If the curvature is greater than the critical curvature, the neutral plane of the material will move towards the outboard tensile area, and the critical buckling position will move towards the neutral plane. Consequently, the half-wavelength of the buckling fibre was relatively stabilised, with the amplitude increasing dramatically. Along with the increasing of the shear modulus, the critical curvature and buckling amplitude increase, while the critical half-wavelength of the fibre buckling decrease and the critical strain of the composite material increase. Finally, we conducted experiments to verify the correction of the key parameters describing SMPC materials under flexural deformation. The values determined by the experiments proved that the theoretical prediction is correct. Additionally, the buckling deformation of the carbon fibre generated a large macroscopic structural strain of the composite material and obtained a resulting large flexural curvature of the structure with minimal material strain of the carbon fibre. (C) 2013 Elsevier Ltd. All rights reserved.

Effects of Ply Angles on Properties of Shape Memory Composite Laminates

Effect of multi‐angle lamination on mechanical properties and damages behavior of carbon fiber reinforced resin matrix composites

Theoretical Analysis of the Buckling Behaviors of Inhomogeneous Shape Memory Polymer Composite Laminates Considering Prestrains

Effect of Z-pin Insertion Angles on Low-Velocity Impact Mechanical Response and Damage Mechanism of CFRP Laminates with Different Layups

Experimental Investigation of Z-pin Insertion Angles on the Mechanical Behavior and Failure Mechanism of Compression after Impact for CFRP Laminates

Modeling on the Effect of Automated Fiber Placement Induced Gaps in Curved Composite Laminates

Increasing the Compressive Strength of Helicoidal Laminates after Low-Velocity Impact upon Mixing with 0° Orientation Plies and Its Analysis

Experimental study on the mechanical behavior of laminates made by fiber steering: Influence of fiber angle and tow width

Bistable Characteristics of Unsymmetric Cross-ply Composite Laminates Considering Different Boundary Shapes

Mechanical Simulation of Thermoplastic Composite Fiber Variable-Angle Laminates

A study on interactive fiber rubber composite structures subjected to bend-twist coupling

Thermomechanical Properties And Deformation Behavior Of A Unidirectional Carbon-Fiber-Reinforced Shape Memory Polymer Composite Laminate

Effects of the Strain Rate Variation on the Interlaminar Stresses of the Thick Angle-Ply Laminates

The Role of Ply Angle in Interlaminar Delamination Properties of CFRP Laminates

Interlaminar Stress and Damage Mechanism of Thermoplastic Composite Laminates

Simulation analysis of parametric effects on consolidation ofangle bended composites

Numerical Elastic-Plastic Simulation of Interlaminar Stresses in a Notched Angle-Ply Thermoplastic Composite Laminate

A Microscale Analysis of Thermal Residual Stresses in Composites with Different Ply Orientations

Post microbuckling mechanics of fibre-reinforced shape-memory polymers undergoing flexure deformation

Mechanical properties and failure mechanisms of composite laminates with classical fabric stacking patterns

Experimental and numerical investigation of stringer's 90° plies optimization of composite material stiffened panels