Abstract:The objective of this study aims to investigate the performance of thermoplastic polyurethane elastomers (TPU)-modified asphalt, with special focus on the influence of polyurethane synthesis parameters upon the performance of base asphalt. In this study, the TPU modifier was incorporated into base asphalt to prepare TPU-modified asphalt by using a self-determined laboratory process. The properties of polyester-based TPU and polyether-based TPU modified asphalt with different contents was analyzed by the base performance tests. The Fourier transform infrared spectroscopy (FTIR), fluorescent microscope, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermal gravity (TG), dynamic shear rheology (DSR), and bending beam rheology (BBR) tests were conducted to expose chemical, microstructure, and rheological properties of the asphalt binders, respectively. The results indicated that the modified asphalt with 5% TPU modifier exhibited a favorable performance in terms of the penetration, ductility, softening point, and rotational viscosity, respectively. The isocyanate and polyol reacted to form carbamate in the TPU-modified asphalt, and moreover the isocyanate and aromatic compounds reacted to form halohydrins in the asphalt. Large particles contained in the polyester-based TPU-modified asphalt increased obviously with the increase of C h (Hard segment content) and r (Isocyanate root index, molar ratio between NCO and OH) value, the fracture mode of it subjected to external load indicated a typical brittle fracture. The content of MDI in the synthesized polyurethane modifier was an important factor affecting the high-temperature stability of the modified asphalt. The polyester-based TPU modifier had a better high temperature performance than the polyether-based TPU modifier. The polyether polyol chain segment showed a greater flexibility as compared to polyester polyol; the addition of polyether polyols can be effectively offset of MDI chain rigidity as r ≤ 1 and C h < 40% leading to the improvement of the viscoelastic property of asphalt. When C h = 40% and r = 0.95, the polyether-based TPU-modified asphalt exhibited the same high-temperature grade as the polyester-based TPU-modified asphalt, whereas the polyether-based TPU-modified asphalt showed obviously higher low temperature grades. The polyester-based TPU with C h = 40% and r = 1 can be used as a modifier to increase the durability of asphalt binders.

Properties of Asphalt Modified by PS at High Temperature

Investigation on Thermo-Rheological Properties and Stability of Sbr Modified Asphalts Containing Palygorskite Clay

Storage Stability of Asphalt Modified by LDPE/SBR

Improved Storage Stability of Ldpe/Sbs Blends Modified Asphalts

Dynamic Mechanical Properties of LDPE/SBR Blend Modified Asphalt

Research on Preparation and High Temperature Behavior of High-Modulus Asphalt

Evaluation of the Thermal Stability and Micro-Modification Mechanism of SBR/PP-Modified Asphalt

Improved properties of polystyrene-modified asphalt through dynamic vulcanization

Effect of Phenolic Resin on the Rheological and Morphological Characteristics of Styrene-Butadiene Rubber-Modified Asphalt

Research on high and low temperature rheological properties of TPU/SBR composite modified asphalt

High-Temperature Characteristics of Polyphosphoric Acid-Modified Asphalt and High-Temperature Performance Prediction Analysis of Its Mixtures

Using SBS/terpene‐styrene resin blends as a novel high‐viscosity asphalt modifier

Influence on Polyurethane Synthesis Parameters Upon the Performance of Base Asphalt

Study on the Performance and Modification Mechanism of Polyphosphoric Acid (PPA)/Styrene–Butadiene–Styrene (SBS) Composite Modified Asphalt

Crumb Tire Rubber Polyolefin Elastomer Modified Asphalt with Hot Storage Stability

Research on Performance of SBS-PPA and SBR-PPA Compound Modified Asphalts

Properties of asphalt modified with ultra-fine full-vulcanized powdered styrene-butadiene rubber and influence of compatilizer

Rheological and Physical Properties of Asphalt Mixed with Warm Compaction Modifier

Enhanced Performance of LDPE/SBS Blend Modified Asphalt Through Dynamic Vulcanization

Physical properties and microstructure of waste rubber powder and SBS complex modified asphalt

Preparation of polymer bitumen binder in the presence of a stabilizer