13 Lumped Kinetic Model and Sub-Model for Catalytic Reforming

ZHAO Liang,FANG Xiang-chen,WANG Hai-yan

DOI: https://doi.org/10.3969/j.issn.1008-1143.2005.04.005

2005-01-01

Abstract:13 lumped kinetic model and sub-model for catalytic reforming designated for increasing benzene and p-xylene yield were proposed so as to abstract the key information on catalytic reforming techniques for more benzene and p-xylene yield.

What problem does this paper attempt to address?

Lumped Kinetics Model and Its On-Line Application to Commercial Catalytic Naphtha Reforming Process

HOU Weifeng,SU Hongye,HU Yongyou,CHU Jian

DOI: https://doi.org/10.3321/j.issn:0438-1157.2006.07.019

2006-01-01

Abstract:Based on the lumping theory and the reaction network with seventeen lumped components reported earlier, a new kinetic model involving twenty lumped components and thirty-one reactions was developed for catalytic reforming process.The subdivision of 8-carbon aromatics and all the hydrocracking reactions of the paraffin lumps were considered in this model.The 20-lumped kinetics model was used to simulate commercial continuous catalytic reforming (CCR) unit.Fair agreement between the calculated and operating data was obtained and the simulation precision of cracking products by the 20-lumped kinetics model was better than that by the 17-lumped model.By adopting an on-line prediction and correction strategy, the 20-lumped model was also used to on-line calculate aromatics yield, yield of each aromatics lump, and RON (octane number of reformate) of the CCR process.The trend and precision of on-line prediction were very good.The average deviations between on-line predicted and actual aromatics yield and RON were 0.52%(mass) and 0.36 respectively,nearly equivalent to the off-line prediction performance.
A dynamic model for naphtha catalytic reformers

Yongyou Hu,Weihua Xu,Hongye Su,Jian Chu

DOI: https://doi.org/10.1109/CCA.2004.1387204

2004-01-01

Abstract:A kinetics-based dynamic model for commercial naphtha fixed-bed catalytic reformers is developed in this paper. The dynamic model is composed of the reforming reaction model, the heater model and the separator model, which is capable to capture the major dynamics that occur in this process system. The lumping details of the naphtha feed and reaction scheme of the reaction model are also given. The simulation results of the model are presented.
Modeling and Simulation of Commercial Catalytic Reformers

胡永有,苏宏业,褚健

DOI: https://doi.org/10.3321/j.issn:1003-9015.2003.04.012

2003-01-01

Abstract:A kinetics-based mathematical model for catalytic reformer was developed for monitoring, planning and optimizing commercial catalytic reformers. The model mainly including reaction model and separation model can predict reaction temperature, concentration profiles, recycle gas composition and octane number of reformate resulting from different feedstocks or operating conditions. The lumping details of the feed with C1~C12 hydrocarbons and reaction scheme were given. A quasi-analytic numerical algorithm with simpler formulation than Runge-Kutta algorithm was used to solve the ordinary differential equations of the model. The reaction kinetic parameters were benchmarked with enough plant data and the differential variable metric optimization method (BFGS) was adopted to estimate these parameters. The model was validated by two kinds of catalytic reforming reformers with different sets of plant data respectively. Agreements between model predictions and plant observations of both reformers were presented.
Simulation, sensitivity analysis and optimization of a continuous catalytic reforming process

Weifeng Hou,Yongyou Hu,Hongye Su,Jian Chu

DOI: https://doi.org/10.1109/WCICA.2004.1343150

2004-01-01

Abstract:A simple kinetic scheme involving 17 lumps and 17 reactions was incorporated in a process model. This model then was used to predict temperature and reformate composition profiles of a commercial reforming process. The agreement between predicted and commercially observed results is very good. The key process variables affecting the reformer yields, such as liquid hourly space velocity (LHSV), the reformer inlet temperature (WAIT), molar hydrogen-to-oil ratio and reaction pressure, were analyzed in detail to guide the selections of naphtha feedstock and operating conditions. Lagrange-Marquardt method was used to solve the nonlinear programming problem with process constraints to optimize process and maximize plant profit. The optimized process variables can bring about 1 percent increase in aromatics yield in weight. The optimization result is approved to not be sensitive to the uncertainty of model parameters.
Modeling, Simulation and Optimization of Commercial Naphtha Catalytic Reforming Process

YY Hu,WH Xu,WF Hou,HY Su,J Chu

DOI: https://doi.org/10.1109/cdc.2003.1272272

2003-01-01

Abstract:A first principles-based dynamic model for a continuous catalyst regeneration (CCR) platforming process, the UOP commercial naphtha catalytic reforming process, is developed in this paper. The lumping details of the naphtha feed and reaction scheme of the reaction model are given. The process model is composed of the reforming reaction model with catalyst deactivation, the furnace model and the separator model, which is capable of capturing the major dynamics that occurs in this process system. Dynamic simulations are performed based on Gear numerical algorithm and method of lines (MOL), a numerical technique dealing with partial differential equations (PDEs). The results of simulation are also presented. Dynamic responses caused by disturbances in the process system can be correctly predicted through simulations.
Modeling, Simulation and Optimization of a Whole Industrial Catalytic Naphtha Reforming Process on Aspen Plus Platform

Hou Weifeng,Su Hongye,Hu Yongyou,Chu Jian

DOI: https://doi.org/10.1016/s1004-9541(06)60119-5

2006-01-01

Abstract:A new 18-lump kinetic model for naphtha catalytic reforming reactions is discussed. By developing this model as a user module, a whole industrial continuous catalytic reforming process is simulated on Aspen plus platform. The technique utilizes the strong databases, complete sets of modules, and flexible simulation tools of the Aspen plus system and retains the characteristics of the proposed kinetic model. The calculated results are in fair agreement with the actual operating data. Based on the model of the whole reforming process, the process is optimized and the optimization results are tested in the actual industrial unit for about two months. The test shows that the process profit increases about 1000yuan·h−1 averagely, which is close to the calculated result.
Eight Lumps Kinetic Model for Residual Oil Catalytic Cracking

Xu Ou-guan,Su Hong-ye,Mu Sheng-jing,Chu Jian

DOI: https://doi.org/10.1109/wcica.2010.5554714

2006-01-01

Abstract:A novel eight lumps kinetic model is proposed to describe the maximizing iso-paraffins process for clean gasoline and propylene technology of residual oil catalytic cracking, in which propylene is lumped separately for accurate prediction. Based on the fluid characteristics in the different reaction zones, a reactor simulation model adopting the combination model of ideal Plug Flow Reactor model and multistage Continuous Stirred-Tank Reactor model is constructed. Unit factors are designed to correct the deviation between model prediction and plant data. The comparison of calculated results with plant data shows that the model could describe the products yields with satisfied accuracy. The proposed model is suitable for on-line soft sensor application.
KINETICS OF P-Xylene LIQUID PHASE CATALYTIC OXIDATION(I) REACTION MECHANISM AND KINETIC MODEL

Youwei Cheng

2003-01-01

Abstract:In this paper, a novel experimental technique for gas-liquid-solid reaction was developed to study kinetics of p -xylene oxidation under the condition of high temperature and pressure. Methyl and aldehyed oxidation during the p -xylene oxidation process was studied according to radical reaction mechanism and recycling of the cobalt-manganese-bromide catalyst. The coupling effect between catalysts and radical reactions was analyzed in detail, and a kinetic model was developed based on the proposed mechanism.Model parameters were determined by data fitting.The model agreed well with the experiments.
Simulation of Industrial Catalytic Reforming Process by Developing User's Module on ASPEN PLUS Platform

HOU Weifeng,SU Hongye,HU Yongyou,CHU Jian

DOI: https://doi.org/10.3321/j.issn:0438-1157.2005.09.021

2005-01-01

Abstract:The industrial catalytic reforming process is simulated by developing the seventeen lumped kinetics model as a user module on ASPEN PLUS platform.The technique of user’s module utilizes the strong databases, complete sets of modules, and flexible simulations tools of the ASPEN PLUS system and retains the characteristics of the self-developed model.Eighteen lumped components (including hydrogen) are defined for more than three hundred compounds in the flowsheet, and special property methods suitable for the petroleum system are selected for the simulation.The developed simulation software is applied to a commercial continuous catalytic reforming process successfully.The simulation results show that fair agreements between the calculated and actual operating data are obtained.
Cstr Model for P-Xylene Oxidation Reactor

Weixing Li,Lijun Wang,Huajie Zhuang,Qinbo Wang,Xi Li

DOI: https://doi.org/10.3969/j.issn.1001-7631.2003.04.007

2003-01-01

Abstract:Rates of chemical reaction and mass transfer were compared to determine the control step of p-xylene liquid phase oxidation process based on the kinetics previously obtained. It was shown that the p-xylene oxidation is controlled by chemical reaction under the industrial oxidation conditions. Therefore, the effect of mass transfer can be ignored and the CSTR model was used to simulate the reactor. The computation results showed that the yield of terephthalic acid increases and the concentration of 4-CBA decreases when the resident time, catalyst concentration, temperature, and/or the mol ratio of Br/Co increases, but the combustion rate of p-xylene and acetic acid increase simultaneously. It was also found that increasing the mol ratio of Co/Mn accelerates the side combustion reactions more remarkably than the main reactions.
Molecular Modeling and Optimization for Catalytic Reforming

SY Hu,XX Zhu

DOI: https://doi.org/10.1080/00986440390255933

2004-01-01

Chemical Engineering Communications

Abstract:In this paper, molecular modeling and optimization for the naphtha catalytic reforming process is studied. The catalytic reforming process is for producing high octane number gasoline by reforming reactions in three sequencing fixed bed reactors. Feed naphtha coming from an atmospheric distillation unit consisted of molecules from C5 to C10 including paraffin, iso-paraffin, naphthene, and aromatic. The molecular reaction network consisted of paraffin cracking, naphthene side-chain cracking, aromatic side-chain cracking, ring opening, ring closure, paraffin isomerization, dehydrogenation, and hydrogenation. A molecular model for catalytic reforming was built. On the basis of the simulation model, a process optimization was performed for feed temperature and pressure under constraints such as benzene content, aromatic content, and RON (Research Octane Number) limitations. High RON was contrasted to low benzene and aromatic content requirements. By optimizing and controlling the reaction pathway, we can obtain a final product with the highest profit and appropriate benzene and aromatic contents and RON value. This example shows significant benefits from applying molecular modeling to optimization in the process level. Since gasoline production is related to many different processes such as reforming, FCC, isomerization, alkylation, and so on, more benefits can be obtained by applying molecular modeling to plant-wide optimization.
Reactor Model of Counter-Current Continuous Catalyst-Regenerative Reforming Process toward Real Time Optimization

Hongbo Jiang,Yun Sun,Shubao Jiang,Zhenming Li,Jianhui Tian

DOI: https://doi.org/10.1021/acs.energyfuels.1c00812

2021-06-11

Abstract:A new kinetic model involving 44 lumped pseudocomponents and 70 reactions for catalytic reforming was developed to satisfy real-time optimization of the commercial counter-current continuous catalyst-regenerative reforming units. The reaction kinetic model was constructed with the equation oriented method, using the orthogonal collocation method to transform the differential equations of the kinetic model into algebraic equations with variables. The sequential quadratic programming method is used to solve the equation oriented model in this study. The validation results showed that the good agreement of material compositions and catalyst coke content at the exit of the fourth reactor, as well as the temperature and pressure at the exit of each reactor, was obtained between simulated values and industrial values. Moreover, the reactor kinetic model is also used to predict the influence of process parameters which is consistent with the trend in actual industrial production. The model makes it possible to find optimal conditions in real-time optimization.This article has not yet been cited by other publications.

energy & fuels,engineering, chemical
Modelling Industrial Catalytic Reforming of Lowoctane Gasoline

D. A. Petrova,P. A. Gushchin,E. V. Ivanov,V. A. Lyubimenko,I. M. Kolesnikov

DOI: https://doi.org/10.1007/s10553-021-01234-x

2021-03-01

Chemistry and Technology of Fuels and Oils

Abstract:Naphtha reforming is one of the most important industrial processes in refineries. The products include aromatic hydrocarbons such as benzene, toluene, and xylenes, which are frillier used as high octane additives to gasoline. To increase the efficiency of the process, it is necessary to develop a new method of naphtha reforming. In this work, we have proposed a mathematical model of catalytic refining of low-octane gasoline fracdons into high-octane fractions. The model is based on kinetic equations, established for commercial gasoline reforming in the presence of the platinum-rhenium catalyst on a γ-Al2O3 carrier in the industrial-scale conditions. The equation: describe the dependence of the content of paraffinic, naphthenic, and aromatic hydrocarbon fractions on the process parameters, including volumetric rate and the reaction temperature. The mathematical model had been validated by comparing calculated results with the industrial data obtained from the commercial naphtha reforming production.

energy & fuels,engineering, chemical, petroleum
Multi-dimensional modeling of non-catalytic partial oxidation of natural gas in a high pressure reformer

Xinwen Zhou,Caixia Chen,Fuchen Wang

DOI: https://doi.org/10.1016/j.ijhydene.2009.12.063

IF: 7.2

2010-01-01

International Journal of Hydrogen Energy

Abstract:A three-dimensional simulation model for non-catalytic partial oxidation of natural gas in a high pressure reformer has been developed. In the model, the numerical methods and submodels conventionally used in turbulent reacting flows are used. The GRI-Mech 3.0 mechanism and a tabulated chemistry approach are applied to model the non-catalytic oxidation of natural gases under high pressures and temperatures. The reactions are assumed to be fast, hence only the equilibrium states of the multi-step reactions are read in an off-line generated chemistry table. This chemistry table has been created using the equilibrium solver EQUIL from the CHEMKIN II package, and the equilibrium values are functions of the initial mixture compositions and the temperatures at a constant pressure. A presumed PDF model is applied to simulate the interactions between turbulent mixing and the multi-step chemical reactions. Simulations have been performed for a commercial natural gas reformer at various O2/CH4 and O2/H2O ratios and pressures in order to investigate the effect of these parameters on the syngas yields. The results have provided some insights into the strategies of solving the hot-spot problem in industrial reformers.
Dynamic modelling and simulation for catalytic reforming unit

Xuemin Tian,Dexian Huang,Guansheng Zheng,Xiqing Zhang,Xuegang Li

1996-01-01

Abstract:Based on the material balance, energy balance and chemical reaction kinetics, a dynamic mathematical model for catalytic reforming unit (CRU) was developed. The distributed parameter model was transformed into a lumped parameter and a solution was brought about by two-dimension Laplace transform and polynomial approximation methods. Simulation results showed that the model could sufficiently lead to the major dynamic effects that occurred in an actual CRU. The model has been applied to the dynamic simulation and training simulator for training of startup, shut down, normal operation and critical failures in CRU.
A New Lumping Kinetic Model for Fluid Catalytic Cracking

Shiyuan Sun,Fandong Meng,Hongfei Yan

DOI: https://doi.org/10.1080/10916466.2018.1519576

IF: 1.695

2018-01-01

Petroleum Science and Technology

Abstract:In the modeling of fluid catalytic cracking reaction, it is necessary to take slurry as an independent lump due to the great difference between feedstock properties and slurry properties. Based on the commercial data and the reaction mechanism of catalytic cracking, the 8 lumped kinetic model including slurry lump and 7 lumped kinetic model excluding slurry lump were developed combined with the characteristics of the MIP (maximizing isoparaffins) reaction. By means of Fourth-order Runge-Kutta integral method and two-swarm cooperative particle swarms optimization method, the kinetic model parameters were estimated, respectively. The average relative error between commercial data and calculated values, as well as the results of product predictions, indicate that the eight-lumped kinetic model has higher prediction accuracy, and the predicted results of slurry yield are more in line with the actual industrial conditions.
Optimization of the Countercurrent Continuous Reforming Process Based on Equation-Oriented Modeling and the SQP Algorithm

Hongbo Jiang,Zhenming Li,Yun Sun,Shubao Jiang,Jianhui Tian

DOI: https://doi.org/10.1021/acsomega.1c04651

IF: 4.1

2022-01-05

ACS Omega

Abstract:Catalytic reforming is a key technology in the petroleum refining and petrochemical industry. In recent years, countercurrent continuous reforming has put forward and practiced the new concept of matching the activity of the catalyst with the difficulty of the reaction. Based on the equation-oriented method, the steady-state model for the reactor-regenerator section of countercurrent continuous reforming was established, including the reactor module, the regenerator module, the compressor model, the heat exchanger model, the heating furnace model, and the oil property model. The inlet and outlet of each module are connected according to the actual technological process, and the model conforms to the requirement of real-time optimization (RTO). The sequential quadratic programming (SQP) algorithm is used for calculation in this study. The model is calibrated to make the calculated value more consistent with the actual value. The model simulation showed the trend of the reforming reaction and the difference between countercurrent reforming and cocurrent reforming. Finally, the process model was optimized for different goals such as the yield of aromatics, the yield of high-octane gasoline, and the yield of C7 + aromatics. These results indicate that the established model can simulate the actual industrial process, which can meet the requirements of RTO, and obtain considerable profits for different optimization objectives.

chemistry, multidisciplinary
Modelling and Optimization Based on the Molecular Matrix for the Overall Refinery Operation

Qi-hong ZHOU,Shan-ying HU,Ding-jiang CHEN,Zhi-wu YU

DOI: https://doi.org/10.3321/j.issn:1009-606X.2005.02.015

2005-01-01

Abstract:To complicated refining processes and stream components, molecular matrices are used to express refining stream compositions. Process models based on molecular matrices are built for catalytic reforming unit, naphtha hydro-treating unit, gasoline stabilizer unit and gasoline blending unit. Molecular compositions can be obtained from stream bulk properties with the conversion model and vice versa. The process models on the basis of molecular matrices can not only give out more detailed molecular information, but also form a common component base for the traditional pseudo-component models in the distillation processes and lumped models in the reaction processes, which makes it possible to integrate multi-process models into an overall plant modeling.
Multi-zone Parallel-Series Plug Flow Reactor Model with Catalyst Deactivation Effect for Continuous Catalytic Reforming Process

Xiao-Jian Dong,Yi-Jun He,Jia-Ni Shen,Zi-Feng Ma

DOI: https://doi.org/10.1016/j.ces.2017.10.007

IF: 4.7

2017-01-01

Chemical Engineering Science

Abstract:Accurate and reliable modeling of continuous catalytic regenerative (CCR) reforming process plays a significant role not only in product and temperature distributions prediction, but also in real-time optimization and control. In this study, a new multi-zone parallel-series plug flow reactor (PFR) model is proposed for the CCR reformer with four-stage stacked radial flow moving bed reactors (RFMBRs). A 27-lumped kinetic model is used to describe the aromatics aimed CCR reforming process. An empirical catalyst deactivation model is designed to describe the axial catalyst activity distribution information and integrated into the multi-zone parallel-series PFR model. The effectiveness of the proposed model is validated by the industrial plant datasets from a commercial reforming process. The zone number of 4 is reasonably determined by balancing the trade-off between the prediction accuracy and computational cost. Moreover, the detailed distributions of component mass fraction, temperature and catalyst activity are thoroughly investigated by means of the simulation results of the 4-zone parallel-series PFR model. The prediction results illustrate that the proposed model could provide accurate predictions of product and temperature distributions, which indicates that the proposed modeling approach could be greatly helpful for assisting in real-time optimization and control of CCR reforming process. (C) 2017 Elsevier Ltd. All rights reserved.
Recent Progress Toward Molecular-Level Kinetic Model for Complex Hydrocarbon Conversion Processes

Zhengyu Chen,Xiangyu Zhao,Jian Wu,Chunming Xu,Linzhou Zhang

DOI: https://doi.org/10.1016/j.cej.2024.150462

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:The simulation and optimization of complex molecular conversion systems are one of the primary challenges in the chemical reaction engineering field. Petroleum refining is a typically complex hydrocarbon conversion system. Building a molecular-level kinetic model for petroleum refining is a crucial basic technology for precisely utilizing petroleum resources. This work briefly describes the typical approach for developing the molecular-level kinetic model. 5 representative frameworks for modeling the molecular-level kinetic model were summarized, containing the single-event approach, bond-electron matrix, structure-oriented lumping, structural unit and bond-electron matrix framework, and molecular type homologous series matrix. The application cases of these frameworks to typical hydrocarbon conversion processes were reviewed. On this basis, this work analyzed the issues and challenges of molecular-level kinetic models for industrial practice. The future direction for the model was also discussed. Moreover, this work believes that building a data-driven model will be the upcoming trend for simulating and optimizing the complex molecular reaction system.

13 Lumped Kinetic Model and Sub-Model for Catalytic Reforming

Lumped Kinetics Model and Its On-Line Application to Commercial Catalytic Naphtha Reforming Process

A dynamic model for naphtha catalytic reformers

Modeling and Simulation of Commercial Catalytic Reformers

Simulation, sensitivity analysis and optimization of a continuous catalytic reforming process

Modeling, Simulation and Optimization of Commercial Naphtha Catalytic Reforming Process

Modeling, Simulation and Optimization of a Whole Industrial Catalytic Naphtha Reforming Process on Aspen Plus Platform

Eight Lumps Kinetic Model for Residual Oil Catalytic Cracking

KINETICS OF P-Xylene LIQUID PHASE CATALYTIC OXIDATION(I) REACTION MECHANISM AND KINETIC MODEL

Simulation of Industrial Catalytic Reforming Process by Developing User's Module on ASPEN PLUS Platform

Cstr Model for P-Xylene Oxidation Reactor

Molecular Modeling and Optimization for Catalytic Reforming

Reactor Model of Counter-Current Continuous Catalyst-Regenerative Reforming Process toward Real Time Optimization

Modelling Industrial Catalytic Reforming of Lowoctane Gasoline

Multi-dimensional modeling of non-catalytic partial oxidation of natural gas in a high pressure reformer

Dynamic modelling and simulation for catalytic reforming unit

A New Lumping Kinetic Model for Fluid Catalytic Cracking

Optimization of the Countercurrent Continuous Reforming Process Based on Equation-Oriented Modeling and the SQP Algorithm

Modelling and Optimization Based on the Molecular Matrix for the Overall Refinery Operation

Multi-zone Parallel-Series Plug Flow Reactor Model with Catalyst Deactivation Effect for Continuous Catalytic Reforming Process

Recent Progress Toward Molecular-Level Kinetic Model for Complex Hydrocarbon Conversion Processes