Abstract:The use of cold-formed steel tubes in the concrete-filled steel tubular (CFST) columns makes the design of the moment connections between beams and CFST columns much more challenging. This is because setting the internal diaphragms in the CFST column to transfer the bending moment of the beam end becomes impossible, and thus new joints are needed. A novel joint was proposed in a previous study by the authors, where two end plates were used for the force transmission between CFST columns and beam flanges. Moreover, to satisfy the “weak member strong joint” requirement, the I-beams were reduced by drilling a series of circular holes in their flanges. However, most of the tested specimens failed by the unexpected rupture of the complete joint penetration (CJP) groove welds between the beam flanges and end plates. In this paper, three specimens are redesigned and tested, where modifications are made to improve their behaviors under the seismic load. In this test, the local buckling of beam flanges at the drilled sections was observed in all specimens, and two specimens failed due to the fracture at the drilled sections, while CJP weld fracture and significant bending of beam flanges both occurred at the failure of the rest specimen. The hysteresis curves of all specimens are fusiform, indicating their good energy dissipations (the maximum equivalent viscous damping coefficients between 0.35 and 0.40). The failure rotation angles are about 2.44–3.01, and the ductility coefficients are between 2.26 and 2.66. According to EC3, all specimens can be classified into the rigid and full-strength joints. Subsequently, the parametric analyses using the validated finite element model are carried out, where the effects of main parameters are investigated on the seismic behavior of the presented joint. This study brings insights into the moment connections between the steel beam and CFST column with the outer cold-formed section.

Research on Seismic Behavior of Connections with Reduced Beam Section (RBS)to Square Concrete-filled Steel Tubular Column with Internal Diaphragm

Nonlinear Finite-Element Analysis of the Seismic Behavior of RC Column–Steel Beam Connections with Shear Failure Mode

EXPERIMENTAL STUDY ON THE SEISMIC BEHAVIOR OF CFST RECTANGULAR COLUMN TO H-SECTION STEEL BEAM CONNECTIONS WITH EXTERNAL STIFFENERS

EXPERIMENTAL INVESTIGATION AND NONLINEAR FINITE ELEMENT ANALYSIS ON THE BEHAVIOR OF CONCRETE-FILLED SQUARE STEEL TUBULAR COLUMN CONNECTIONS

Experimental Study on Reduced I-beam to CFRST Column Joints under Cyclic Loading

Reserch on Perforemance of Connections with Reduced Beam Section(RBS) to Square Concrete-filled Steel Tubular Column with Internal Diaphragm

Seismic Behavior of Exterior Connections with Steel Beams Bolted to Cft Columns

Seismic Behavior of an Improved Drilled Flange Connection for I-beam to CFST Column

Seismic Behavior of Concrete-Filled Wide Rectangular Steel Tubular (CFWRST) Stub Columns

Experimental Research on End-plate Bolted Connection with Steel Beam and Reinforced Concrete Column

Experimental behaviour of steel reduced beam section to concrete-filled circular hollow section column connections

Research on Shear Performance of Concrete-Filled Square Steel Tubular Column Connections

Seismic Performance of the Concrete-Encased CFST Column to RC Beam Joints: Analytical Study

Seismic behavior of a new through-core connection between concrete-filled steel tubular column and composite beam

Experimental Study on Seismic Behavior of Connections Composed of Concrete-Filled Square Steel Tubular Columns and Steel-Concrete Composite Beams with Interior Diaphragms

Experimental research on seismic behavior of concrete-filled square steel tubular column connections with exterior diaphragms

Nonlinear FEM Analysis of Steel Beam-to-Concrete Filled Steel Square Tube Column Connections with External Stiffening Rings

Experimental and numerical investigation of through-diaphragm in H-shaped steel beam to CFST column connections

Seismic Behavior of Connections Composed of CFSSTCs and Steel–concrete Composite Beams — Finite Element Analysis

Seismic Behavior of Composite Connections — Flexural Capacity Analysis