Application of Local- Bus Protocal for Field Bus

Heng Yu,Chun-yu ZHAO,Da-yue CHEN

DOI: https://doi.org/10.3969/j.issn.1003-7241.2005.09.014

2005-01-01

Abstract:This paper presents a scheme of local-bus communication technology which is realized only by software. This local-bus technology has been applied successfully in several projects.

What problem does this paper attempt to address?

Survey on Control Research of Networked Control Systems Based of Field Bus

LIU Gui-guo,LIU He,HUANG Dao

DOI: https://doi.org/10.3969/j.issn.1671-9565.2006.01.015

2006-01-01

Abstract:In view of control,the research background and contents on the networked control systems based of field bus are introduced in this paper.Networked control systems is a discipline as the combination of network and control science which covers a wide subjects.First,the three mathematic models of networked control systems are discussed, which consist of short network-induced delay with the controller time or event driven,and long network-induced delay with the controller event driven.Second,the mean value controllability,mean square controllability, mean value observability and mean square observability of networked control systems are analyzed. Third,several methods of controller design under the conditions of networked systems are intrduced.Finally.a further discussion on performance improvement of networked control systems in the furture is proposed.
Design and implementation of controller for a sensor network protocol

Chunhua Ju,Xin Yuan,Jianguo Xing,WenMin Zhao,Weiwei Zhu,Jing Huang

2007-01-01

Abstract:This paper presents the design and implementation of network controller which based on the Data Link Layer's specification of a lightweight sensor-oriented fieldbus protocol, that is sensor network protocol. The controller is packed with AVALON standard peripheral interface. It can be treated as a normal intellectual property core in project design, so that the operation on it is simplified as reading or writing on register. The test results show that the controller meets the requirements of the specification in the frame identification, arbitration, checking and so on. A follow-up application developing basement can be found easily on this controller.
The IRCBus Communication Protocol Construction Design and Realization for Distributed Control System

Lei Wang,Xi Wang,Minling Zhu

DOI: https://doi.org/10.2514/6.2010-8848

2010-01-01

Abstract:Distributed control system plays an important part in the application of satellite systems. However, there are integrated requirements (i.e., reliability, real-time capability, expandability, commonality, usability, economy and efficiency) for communication in these systems often used in hostile environments. The work presented here relates to a protocol named IRCBus (Industry High-Reliability Configurable Bus), which supports these requirements. And it also offers practical solutions. First of all, the protocol is formulated based on ISO/OSI (International Organization Standardization /Open System Interconnection) model and it includes four layers: Physical, DataLink, Network and Transport. And it proposes new ideas and improved methods in each layer draft and realization for these requirements. Then the high reliability is guaranteed by hot backup, three redundancy, bus isolation, retransmission law, data check and intrinsically safe explosion-proof; the real-time capability is realized by hardware system based on Field Programmable Gate Arrays (FPGA) and software system; the expandability for bus functions and network size is considered during the whole design; the usability is solved by system management function, installing law and uninstalling law; the low cost are achieved as follows: adopting common cable as transmission media; utilizing existing chip RS485 chip with rational circuit; the efficiency is improved by taking advantage of 8-bit data and 9-bit data in UART (Universal Asynchronous Receiver/Transmitter) protocol and other features. Moreover, it analyzes the protocol from communication principle perspectives. Lastly, in conclusion, it provides some discussion about extensions for Presentation layer (the sixth layer in ISO/OSI) and bus drive. rds: Protocol, IRCBus, Field bus
Real-time Communication Using Foundation Fieldbus

Yue Zhou,Zhi Wang,Tian-ran Wang,Hai-bin Yu

DOI: https://doi.org/10.1007/978-3-662-07219-6_13

2003-01-01

Abstract:Local area networks (LANs) are becoming popular in industrial computercontrolled systems increasingly. Broadcast LANs aimed at the interconnection of sensors, actuators and controllers are commonly known as fieldbus networks. Recently, the vendor-specific fieldbus has being substituted by vendor-independent standardized fieldbus, which supports the open system concept and has started to be used commonly. Particular relevance must be given to the IEC 61158 (1999), which encompasses eight widely used fieldbuses: FF HI, ControlNet, PROFIBUS, P-NET, FF HSE, SwiftNet, WorldFIP and Interbu (Xiuju 2000; Xiong 2000) known that time constraints are more stringent as we go down in the automation hierarchy. In this charter, we consider time constraints or deadlines as the maximum allowable time span between a message transfer request and its transmission on the bus. In fact, the total message cycle delay results from multiple factors, such as the access and queuing delays, the transmission time (frame length / transmission rate) and the protocol processing time. As we are dealing with realtime communication across a shared transmission medium, we focus our analysis on the access delay and queuing delay factors. These factors depend on the MAC (Medium Access Control) mechanism used by the fieldbus network. Fieldbus, as infrastructure of communication to support real-time traffic among field devices in factory floor, is one of typical real-time network. According to real-time application, protocol of MAC layer of fieldbus can be divided into event-triggered and time-triggered. The former does not support the real-time application directly and usually uses CSMA (Carrier Sense Multiple Access), like CAN and LON. The latter supports the real-time application directly and often uses token. Further, the time-triggered can be sub-divided into three classes: 1) centralized token in WorldFIP and Foundation Fieldbus; 2) distributed token in PROFIBUS and FDDI; 3) virtual token in P-Net. Recently, several studies on the ability of fieldbus networks to cope with realtime requirements have been presented, such as those by Tindell and Zuberi on
Application of LIN Bus in Vehicle Network

yanyan xu,jingcheng wang,wenxin chen,jin tao,qiujuan liu

DOI: https://doi.org/10.1109/ICVES.2006.371566

2006-01-01

Abstract:This paper presents a door control system which is based on Freescale groupware. The main hardware and software realization is summarized as the whole system design. The Final test of our prototype with real sensors and actuators validate our proposed system design, which could replace the existing system through further industrial validation.
Applied Fieldbus into Communication Systems in ITS

Min Li,Hui Wang,Ping Li

DOI: https://doi.org/10.3969/j.issn.1002-0268.2001.06.021

2001-01-01

Abstract:After the communication system in ITS is introduced briefly, its hierarchy of the communication system is presented. By analyzing the strong and weak points of standardized fieldbus, a new hierarchy communication system framework is presented in the paper, in which the widely accepted standards of higher layer are kept unchanged while the lower layer taking a new solution based on modified fieldbus. In order to demonstrate the feasibility, a prototype system is introduced.
Whole Transformer Station Protection and Automation-a Local Area Network Approach

Q YANG,Y ZHAO,R WATSON

1993-01-01

Abstract:The authors introduce an approach to whole transformer substation protection and automation. It describes a local area network (LAN) technique which is especially suitable for power system automation. The LAN permits the interconnection of protection systems, fault recorders, and the host computer. The host computer coordinates the functioning of the equipment in the whole substation, passes any messages from protection relays or fault recorders to a remote control room. The control staff can interact through the host computer with any relay or recorder to effect a change or interrogate the equipment. The LAN uses BITBUS interconnection standards with an isolated dual-host computer with an advanced bus. The system can transmit at a rate of either 375 kbps or 62.5 kbps over a maximum distance (without repeater) of 1200 metres
LIN Bus Data Analyzing System Based on PSoC and WirelessUSB Technology

XUE Xiao-jun,YAO Wei,ZHANG Wei,SONG Zhi-ning

DOI: https://doi.org/10.3969/j.issn.1001-4551.2008.02.016

2008-01-01

Abstract:With the extensive using of local interconnect network(LIN) bus protocol in automotive network,the developing of the LIN bus analyzer is impatiently desired.A LIN bus data analyzer in software and hardware,in virtue of system on chip PSoC CY929466 and Wireless technologies was presented.Through the strictly test,this system works stably and robust.This project also shows the convenience of wireless technology and low cost,the flexibility of PSoC technology.
Design and Implementation of Field Bus Device Management System Based on HART Protocol

Tao Li,Ze Dong

DOI: https://doi.org/10.1109/imcec.2018.8469220

2018-01-01

Abstract:The highway addressable remote transducer (HART) was introduced in detail, on the basis, a field bus device management system based on HART protocol was designed. This system adopt C/S mode, and has the function of reading, writing as well as diagnosis, adjustment and management of devices parameters. Meanwhile, this article focus on solving the situation when there is no EDDL file, which is realizing the management of HART universal devices and HART dedicated devices based on the classification of commands in the HART protocol in order to complete the test and make the system to be steady state finally.
Design of a High Speed Field Bus Control System Based on the ARM Processor

Xu Yang

2007-01-01

Abstract:With the rapid development of field bus, embedded system and Ethernet technology, the field bus controller has been required more than before. Combine all the technology above is the trend of the modern industry, and is the requirement for realizing the intelligence, networks and remote control as well. This paper mainly contains the following contents: choose the hardware of intelligent slave based on Profibus-DP, config the uClinux system and the study on control algorithms.
Application of LIN-bus to Seat and Rear-mirror Control System

Nie Dangen,Yao Wei,Zhang Wei,Qin Guoping

DOI: https://doi.org/10.3321/j.issn:1000-680X.2007.07.014

2007-01-01

Abstract:A car body control network for seat and rearmirror is constructed based on LIN bus,and the control of seat and rear-mirror with memory function is realized.Based on this,the functions of low power consumption and fault-self-diagnosis are also designed for the system,so the cost is reduced,providing a good solution for practical application.
A Compatibleness Technology of Fieldbuses Based on Protocols Chip

Tian Xiaohua,Shi Haoshan

DOI: https://doi.org/10.3321/j.issn:1002-8331.2006.06.045

2006-01-01

Abstract:The article represents a compatibleness technology based on Protocols Chip,analyzes the pivotal technology to implement the Protocols Chip and brings forward the design concept of Protocols Chip.With the analysis of the application of Protocols Chip in a electrical monitoring and control system,the article illustrates the architecture and work flow of the communication module based on Protocols Chip and makes a quantitative analysis on the Real-time quality of the Protocols Chip.
Application of Fieldbus Technology in Substation Integrated Automation System

Danyang Li,Chundong Song,Lili Xu

DOI: https://doi.org/10.18686/AHE.V4I12.3203

2021-03-24

Abstract:The development of fieldbus technology is an industrial data bus technology in the field of electrical engineering and automation. It can solve the problem of digital communication between intelligent instruments, controllers, actuators and other field devices. In addition, it can also effectively solve the problem of information transmission between these field control devices and advanced control systems. This paper analyzes the application of this technology combined with a number of engineering examples.

Engineering,Computer Science
Field Bus Technique and Automation of Engine Room

Wei LI,Jian-ming CAO

DOI: https://doi.org/10.3969/j.issn.1674-5949.2002.02.007

2002-01-01

Abstract:Field bus technique and its application in the respect of the automation of engine room are outlined in the paper and the emphasis is placed on CAN field bus technique and its adoption in ships. Examples are combined to introduce the configuration of automatic systems of engine room and the development of CAN module.
A Realization of Remote Monitor and Control System of Web-Based Field Bus

杨冬松,要义勇,赵丽萍

DOI: https://doi.org/10.3969/j.issn.1001-3881.2003.04.039

2003-01-01

Abstract:It is a kind of innovation of traditional controll technology to use WEB technology to realize the remote monitor and control of the field bus. The architecture of Web-based remote monitor and control system of field bus is designed in this paper, and the function of remote information platform is built on the basis of RTDBS technology, and so the question of industrial real-time data publishing based on WEB is resolved; The function of remote monitor and control platform is realized on the basis of CORBA and XML technology, and so remote control of industrial equipment is also realized.
Realtime Characteristic of FF Like Centralized Control Fieldbus and Its State-of-art

Z Wang,Z Yue,JM Chen,YQ Song,YX Sun

DOI: https://doi.org/10.1109/isie.2002.1026055

2002-01-01

Abstract:The temporal property of MAC protocol of fieldbus is critical to meet real-time constraints of field devices in factory floor. Among various types of MAC protocols, the one using centralized strategy is characterized by providing a feasible schedule to meet different temporal constraints of field devices online, and also providing schedulability analysis offline a priori. WorldFIP and FF, two popular international standards of fieldbus, both adapt a centralized strategy, which is mainly implemented by schedule table (ST). This paper mainly discusses how to construct ST including size of ST schedule algorithm and schedulability analysis, to meet requirement of field devices on response time, jitter, synchronization, and its state-of-the art.
Bus Simulation System Based on Wireless Communication and Sensor Network

Rui-dong Zhang,Tian-yuan Chen,Xin-feng Shen,Zi-chen Zheng,Kai Hu

DOI: https://doi.org/10.1109/wcsn.2014.75

2014-01-01

Abstract:With the considerable development of city bus system, people have been troubled by the scarcity of city bus, traffic jam and inaccuracies of stations speaker system. Based on the problems, the simulation system implements accurate positioning of the buses by using multiple wireless modules for wireless communication and applying SCM (Single Chip Microcomputer) to be the central data processing unit.
THE DESIGN OF THE PLC NETWORK CONTROL SYSTEM OF FIELDBUS-BASED AND CONFIGURATION SOFTWARE

Shi Yiping,Zhao Minyuan,Liu Qizhong,Bai Yingcai

DOI: https://doi.org/10.3969/j.issn.1000-386X.2006.03.012

2006-01-01

Abstract:Based on the analysis of the fieldbus technology and the work of the tunneling devices,this paper mainly presents the design scheme of the PLC network control system of fieldbus-based and configuration software.It has great significant to raise the reliability of tunneling devices and improve the quality of engineering.
Application of fieldbus in monitoring and control system for automobile jointinga assembly line

Wei-han ZHANG,Heng LIN,Shou-hua YUAN,Zan-dong HAN,Da-yong JIN,Tai-hui PENG,Bao-qang LIN,Fa-gang LIU

DOI: https://doi.org/10.3969/j.issn.1001-3997.2001.02.017

2001-01-01

Abstract:In this paper, the idea of Fieldbus and application of Compobus/D network are introduced. A monitoring and control system for automobile jointing assembly line is taken for example to analysis several usually used methods in dealing with the monitoring and control system. Some advantages of Fieldbus are pointed out.
Brief Introduction to DCS and the Fieldbus Technology

ZHANG Zhen,NIU Yu-gang

DOI: https://doi.org/10.3969/j·issn.1000-3886.2013.01.002

2013-01-01

Abstract:The fieldbus technology is very significant to the industry. First the definition、development and composition of Distributed Control System is briefly introduced in the paper .Then,the present application situation and latest developments of the fieldbus technology are discussed from the aspect of the formation background、conception、feature、advantages and composition. Some types of popular national Fieldbuses such as CAN、LonWorks、FF、HART 、Profibus and the communication protocol 、applied field、real-time and the solution of dealing with the changes in technology and system failure are also introduced.

Application of Local- Bus Protocal for Field Bus

Survey on Control Research of Networked Control Systems Based of Field Bus

Design and implementation of controller for a sensor network protocol

The IRCBus Communication Protocol Construction Design and Realization for Distributed Control System

Real-time Communication Using Foundation Fieldbus

Application of LIN Bus in Vehicle Network

Applied Fieldbus into Communication Systems in ITS

Whole Transformer Station Protection and Automation-a Local Area Network Approach

LIN Bus Data Analyzing System Based on PSoC and WirelessUSB Technology

Design and Implementation of Field Bus Device Management System Based on HART Protocol

Design of a High Speed Field Bus Control System Based on the ARM Processor

Application of LIN-bus to Seat and Rear-mirror Control System

A Compatibleness Technology of Fieldbuses Based on Protocols Chip

Application of Fieldbus Technology in Substation Integrated Automation System

Field Bus Technique and Automation of Engine Room

A Realization of Remote Monitor and Control System of Web-Based Field Bus

Realtime Characteristic of FF Like Centralized Control Fieldbus and Its State-of-art

Bus Simulation System Based on Wireless Communication and Sensor Network

THE DESIGN OF THE PLC NETWORK CONTROL SYSTEM OF FIELDBUS-BASED AND CONFIGURATION SOFTWARE

Application of fieldbus in monitoring and control system for automobile jointinga assembly line

Brief Introduction to DCS and the Fieldbus Technology