Abstract:Abstract In this paper, the working parameter optimization of strengthen waterjet grinding by employing the orthogonal-experiment-design-based ANFIS (Adaptive Neural Fuzzy Inference System), was conducted to obtain an optimal result of bearing ring machining. An improved ANFIS system based upon orthogonal experiment design, was proposed to optimize the working parameters in grinding practices, which increases the surface hardness of ring surface from 49.0 to 72.0 HRC, topography elasticity variance from 330.0 to 670.0, texture energy from 24.5 to 88.0, decreases the surface roughness from 0.65 to 0.25 (upmu ) m, and loading deviation from 1860.5 to 1320.0, thereafter an optimal grinding quality can be obtained. The optimization approach proposed involve the following steps: Preparation of experimental environment; Measure index determination for ring surface; Orthogonal experiment design for making fuzzy logic rules; Establishment of ANFIS system; Working parameter optimization for waterjet grinding; and Performance verification for actual grinding. Objective of this research is determining the optimal working parameters with fewer experimental iterations compared to other alternative approaches, such as Genetic parameter optimization, SA–GA parametric prediction, Taguchi parameter estimation, ANN–SA parametric selection, and GONNs parameter selection method. Statistical analysis and result comparisons support its efficiency and reliability in machining practices, a stable and reliable grinding process can be achieved for typical conditions by using waterjet pressure at around 310ṀPa, flow rates of water mass at about 5.8 kg/min, attack angle by 60–75 ({^{circ }}) , mass rate of abrasive grit by about 0.4 kg/min, and traverse speed by 60 mm/min. It was concluded that this proposed ANFIS system can be used as a suitable and effective tool, to investigate the complicated influential correlation between waterjet working parameters and grinding effectiveness in bearing manufacturing, and to give a better machining performance compared to other experimental practices.

Optimization of process parameters when finishing hole by fluid magnetic abrasives

Parametric Studies on Finishing of AZ31B Magnesium Alloy with Al2O3 Magnetic Abrasives Prepared by Combining Plasma Molten Metal Powder with Sprayed Abrasive Powder

Experimental Research on Optimizing Processing Parameters of Ultrasonic Polishing without Abrasive

Morphology characterization of polishing spot and process parameters optimization in magnetorheological finishing

Technological parameter optimization and quality effects on solid-liquid phase abrasive flow polishing

Investigations on process parameters of cluster magnetorheological polishing in a planet motion model

Process Parameter Modeling and Optimization of Abrasive Water Jet Dressing Fixed-Abrasive Pad Based on Box–Behnken Design

Comprehensive evaluation of process parameters optimization for sheet piercing assisted by magnetic medium based on grey relational analysis

Influence of Excitation Parameters on Finishing Characteristics in Magnetorheological Finishing for 6063 Aluminum Alloy

Optimizing Parameters for Magnetorheological Finishing Supersmooth Surface

Dynamic magnetic field magnetorheological finishing with constant load and variable gap

Multiobjective optimization of magnetic abrasive finishing process with periodic re-distribution of magnetic abrasive particles on 17-4PH stainless steel

Process optimization and finite element modeling in magnetorheological abrasive finishing of SS-316L with surface characterization

Influence of Process Parameters and Initial Surface on Magnetic Abrasive Finishing of Flat Surfaces on CNC Machine Tools

Working parameter optimization of strengthen waterjet grinding with the orthogonal-experiment-design-based ANFIS

Experimental investigation on the effet of input paramètres on surface roughness and MRR of abrasive flow machining process

Experimental Investigation on Magnetic Abrasive Finishing for Internal Surfaces of Waveguides Produced by Selective Laser Melting

Modeling and simulation of the action mechanism of multi-particles in magnetic abrasive finishing for internal blind cavity using the discrete element method

Finishing mechanism modelling on magnetic abrasive finishing behaviours with core-shell magnetic abrasive particles

Evaluation and Optimization Method of High Speed Cutting Parameters Based on Cutting Process Simulation

Multi-objective optimization of machining parameters in micro-milling LF 21 based on the AHP-entropy weight method