Abstract:The effects of an α-Al2O3 nanoparticle filler in the SiC matrix on the mechanical properties and failure mechanism of the unidirectional, laminated carbon fiber-reinforced SiC composites were investigated in this work. First, α-Al2O3 nanoparticles were added to the carbon fiber bundles using a slurry impregnation method, and then the Cf/SiC composite with an α-Al2O3 nanoparticle filler (Cf/SiC-Al2O3) was fabricated using a precursor infiltration and pyrolysis method. The microstructure of the Cf/SiC-Al2O3 composite showed chemical compatibility between the α-Al2O3 and the pyrolysis SiC. The Cf/SiC-Al2O3 composite with a low porosity of ~6.67% achieved a good flexural strength of 629.3 MPa and a good fracture toughness of 25.2 MPa·m1/2. The interlaminar shear strength of the Cf/SiC-Al2O3 composite was 11.7 MPa. The SiC-Al2O3 matrix also presented a considerable Young’s modulus of 138.2 ± 8.66 GPa and hardness of 10.3 ± 1.03 GPa. Further analysis indicated that the good mechanical properties with the addition of an α-Al2O3 filler were not only related to the dense matrix and the improvement of the mechanical properties of the matrix. They also originated from the thermal residual compressive stress in the SiC matrix close to the α-Al2O3 nanoparticles caused by the thermal expansion mismatch, which could reflect and close the cracks in the matrix. The findings of this study provide more methods for designing new composites exhibiting a good performance.

Effect of Volume Fraction on Microstructure and Mechanical Properties of Si3N4/Al Composites

Effect of volume fraction on microstructure and mechanical properties of Si3N4/Al composites

Effect of High Temperature Diffusion on Microstructure and Mechanical Performance of Si/1199Al Composites

The Mechanical Properties of Co-Continuous Si3N4/Al Composites Manufactured by Squeeze Casting

Mechanical properties and damping capacity of SiC p /TiNi f /Al composite with different volume fraction of SiC particle

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

A Study of microstructure and mechanical property of Si 3N 4p/2024Al composite

Fabrication and mechanical properties of high-volume-fraction Si 3 N 4 -Al-based composites by squeeze infiltration casting

Effect of Infiltrated Eutectic AlSi on the Microstructure and Properties of C/C Composites

Influence of Cu content on interfacial structure and mechanical properties of 3Al2O32SiO2 fiber reinforced Al matrix composites

Strengthening mechanism and anisotropy of mechanical properties of Si3N4p/Al-Mg-Si composites fabricated by sintering and extrusion

Effect of Cu Content on Microstructure and Properties of Al2o3-Sio2 Fiber Reinforced Aluminum Matrix Composites

Microstructure and Mechanical Properties of Unidirectional, Laminated Cf/SiC Composites with α-Al2O3 Nanoparticles as Filler

Microstructure elaboration and mechanical properties of AlN_p/4032Al composite

Microstructure and Mechanical Properties of 45 vol.% SiC p /7075Al Composite

Effect of porous Si 3 N 4 preform on the mechanical properties of Si 3 N 4 /Al composites with interpenetrating network structure

Effect of Nano-Sic Content on Mechanical Properties of Sic/2014al Composites Fabricated by Powder Metallurgy Combined with Hot Extrusion

Numerical Simulation of the Mechanical Properties and Fracture of SiCp/6061Al Composite Materials Based on Microstructure

Effect of SiC particulate on the microstructure of Al-6Ti-6Nb matrix composites fabricated by mechanical alloying technique

Influence of Cu content on interfacial microstructure of Al2O3-SiO2 fiber reinforced Al matrix composites

Effects of nanoparticles on the solution treatment and mechanical properties of nano-SiCp/Al-Cu composites