Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

The Novel N-rich Hard Carbon Nanofiber As High-Performance Electrode Materials for Sodium-Ion Batteries

Electrode Materials: A Hierarchical N/S-Codoped Carbon Anode Fabricated Facilely from Cellulose/Polyaniline Microspheres for High-Performance Sodium-Ion Batteries (Adv. Energy Mater. 6/2016)

A Hierarchical N/S‐Codoped Carbon Anode Fabricated Facilely from Cellulose/Polyaniline Microspheres for High‐Performance Sodium‐Ion Batteries

Low Temperature Carbonization of Cellulose Nanocrystals for High Performance Carbon Anode of Sodium-Ion Batteries

Achieving High Initial Coulombic Efficiency for Competent Na Storage by Microstructure Tailoring from Chiral Nematic Nanocrystalline Cellulose

Direct Chitin Conversion to N-doped Amorphous Carbon Nanofibers for High-Performing Full Sodium-Ion Batteries

A facile strategy toward sodium-ion batteries with ultra-long cycle life and high initial Coulombic Efficiency: Free-standing porous carbon nanofiber film derived from bacterial cellulose

N,S co-doped biomass hard carbon/ZnS composite as the anode material for high-rate sodium-ion batteries

Sustainable Fabrication of a Practical Hard Carbon Anode for a Sodium-Ion Battery with Unprecedented Long Cycle Life

Electrospun Sb/C Fibers for a Stable and Fast Sodium-Ion Battery Anode.

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

N, S self‐doped porous carbon with enlarged interlayer distance as anode for high performance sodium ion batteries

N, S Co-Doped Porous Carbon Nanospheres with a High Cycling Stability for Sodium Ion Batteries

A Stable Biomass‐Derived Hard Carbon Anode for High‐Performance Sodium‐Ion Full Battery

Carbon Nanofibers Derived from Cellulose Nanofibers As A Long-Life Anode Material for Rechargeable Sodium-Ion Batteries

Hybrid-Mechanism Synergistic Flexible Nb2O5@WS2@C Carbon Nanofiber Anode for Superior Sodium Storage

Hard Carbon/graphene Microfibers As a Superior Anode Material for Sodium-Ion Batteries

Sb/N‐Doped Carbon Nanofiber as a Sodium‐Ion Battery Anode

Waste-to-wealth: low-cost hard carbon anode derived from unburned charcoal with high capacity and long cycle life for sodium-ion/lithium-ion batteries

A synthesis strategy of 3D carbon nanosheet anode with adsorption/intercalation-filling hybrid mechanism for high-performance sodium/potassium-ion batteries

Boosting the Initial Coulomb Efficiency of Sisal Fiber-Derived Carbon Anode for Sodium Ion Batteries by Microstructure Controlling