Abstract:Variable cycle engine (VCE) is one of the ideal power units for advanced multipurpose aircraft. The addition of bypasses and adjustable mechanisms in the compression system enables the VCE to adjust the mass flow distribution according to the flight mission and expand the flight envelope. However, it also leads to strong aerodynamic coupling and complex matching relations between components. Therefore, it is necessary to develop an integrated design method for variable cycle compression system. Through-flow design and analysis are important steps in aerodynamic design, which determine the meridional flow path and blade section parameters for compression system. An integrated through-flow design and analysis program for double bypass variable cycle compression system called SCAD was proposed. In the program, the whole computing domain was divided into three uninterrupted flow paths according to the position of the two splitters. Pairs of split streamlines and overlapped computing stations were set up to ensure the continuity of the flow parameters and the convergence of the iteration. It can achieve integrated coupling simulation of the front fan (FF), the rear fan (RF), and the high pressure compressor (HPC), and solve the matching problem of the variable cycle compression system in the preliminary design. The errors of total pressure ratio and isentropic efficiency of most stages simulated by SCAD are no more than 2%, and the spanwise distributions of the key aerodynamic parameters at main flow field at each stage are consistent with the 3D CFD results, as shown in verification of a double bypass variable cycle compression system. SCAD has been applied in the design system of variable cycle compression system in China now. Finally, the influence of the outer bypass ratio on the aerodynamic performance of the front/rear fan of the double bypass variable cycle compression system was studied by using SCAD. The results shows that the bypass ratio has little effect on the front fan, whereas the total pressure ratio and isentropic efficiency of the rear fan increase with it. When the bypass ratio is small, the increase of axial and radial velocities leads to blockage in the core flow path and decrease of rotor load. The forward blade of the tandem stator works at a large-negative-incidence condition, making the performance of the rear fan deteriorate sharply. It is reasonable to choose the design bypass ratio of the front/rear fan as 0.33.

Effect of Load Distribution at the Roots among Stages on Performance of a High Bypass-ratio Fan/Booster

An Optimization on the Stacking Line of Low-Pressure Axial-Flow Fan Using the Surrogate-Assistant Optimization Method

Optimization Design of Centrifugal Fan Impeller Based on Numerical Simulation.

A throughflow-based optimization method for multi-stage axial compressor

Fan Root Aerodynamics for Large Bypass Gas Turbine Engines: Influence on the Engine Performance and 3D Design

Aerodynamic Optimization of a Fan/Booster Stage Blade in an Overall Engine Environment

Numerical investigation of the aerodynamic performance and loss mechanism in a low bypass ratio variable cycle engine fan

Application of Complex 3D Aerodynamic Layout in Highly Loaded Compressor on Numerical Simulation

A design method of volute profile of multi-blade centrifugal fan based on DRBF model

Design Optimization of the Last Stage of a 4.5-Stage Compressor Using a POD-based Hybrid Model

Numerical Investigation on the Effects of Gap Circulating Flow on Blower Performance under Design and Off-Design Conditions

Effect of Meridional Shape on Performance of Axial-Flow Fan

The Blade Shape Optimization of a Low-Pressure Axial Fan Using the Surrogate-Based Multi-Objective Optimization Method

The matching characteristics and flow mechanisms of partial-height booster rotor and fan rotor for a high-throughflow fan

Performance Improvement of a Large Capacity Roots Blower Based on Profile Modification

Experimental and numerical simulation investigation of a counter-rotating fan stage

Diagnosis and Design Improvement of the Internal Flow Field in an Automotive Cooling Fan Based on Boundary Vorticity Dynamics, Part I: Blade Profile Scaling and Rotation

Numerical Study and Experimental Validation of a Roots Blower with Backflow Design

Study on Integrated Through-Flow Method for Variable Cycle Compression System

Design and Performance Analysis of a Two-Stage Transonic Low-Reaction Counter-Rotating Aspirated Fan/compressor with Inlet Counter-Swirl

Aerodynamic Design and Performance Analysis of a Vaneless Counter-Rotating Fan and Compressor