Abstract:Introduction This study create a dental composite by hybirding polyhedral oligo-sesquioxide nano monomers and bioactive glass BG 45S5. Methods Make a experimental composite resin material with a 60% filler content overall by substituting 20% of the filler with BG 45S5. The experimental resins are grouped and named P0, P2, P4, P6 and P8 based on the reactive nanomonomer methacrylic acid-based multifaceted oligomeric sesquisiloxane (POSS) added by 2%–8% in the resin matrix portion of each group. Utilize universal testing machine to analyze and compare the mechanical properties of these, then performed Fourier infrared spectrum analysis, double bond conversion analysis, and scanning electron microscope analysis. Based on this, after soaking the experimental materials artificial saliva solution or the lactic acid solution for a while, the pH changes of the solution, the release of Ca 2+ and PO 4 3− ions, and the precipitation of apatite on the resin material's surface were tested and analyzed. Cell viability tests were used to assess sample cell viability and quantify the cytotoxicity of biological cells. The independent sample t test was used to examine the group comparisons, and a difference was considered statistically significant when P <0.05. Results Outstanding mechanical and the double bond conversion are demonstrated by the nanocomposites when the POSS concentration hits 4wt%. Agglomeration will cause the performance to deteriorate if the concentration beyond this threshold. In the P4 group, the double bond conversion, CS, and FS rose by a large margin, respectively, in comparison to the blank control group P0. Thankfully, the data demonstrate that adding POSS increases adhesive ability when compared to the blank group P0, however, there is no discernible difference between the other experimental groups. The acid neutralization capacity of the P4 group is essentially the same as that of the control group (P0). Ca 2+ and PO 4 3− ions are released in significant amounts following treatment with lactic acid solution, although this tendency is clearly less pronounced in artificial saliva. SEM and EDX data indicate that when the experimental resin is soaked to a lactic acid solution and artificial saliva, apatite precipitation will happen on its surface. The results of the cell viability test indicated that there was no statistically significant difference between the experimental groups, and the viability of the cells increased after 24 and 48 hours. Conclusions POSS was included into the composite resin along with 20% bioactive glass as a filler. When the proportion of POSS is less than 4%, the indices of composite resin materials rise in a dose-dependent way. When this value is surpassed, performance begins to deteriorate. The inclusion of POSS has no influence on the biological activity of the composites, which means that the hybrid composite resin is capable of acid neutralization, ion release, and apatite precipitation. Clinical Significance The experimental composite resin can be used as an intelligent material in clinical treatment. It has the clinical application potential of preventing demineralization of tooth hard tissue, promoting remineralization and improving edge sealing through apatite precipitation.

Preparation and Characterization of Composite Resin Containing Anion Powder

Synthesis and Characterization of an Anti-Caries and Remineralizing Fluorine-Containing Cationic Polymer PHMB-F.

Development of Novel Polymerizable Antibacterial Monomer and Its Antibacterial Effects on Dental Adhesive

Study on the mechanical and aging properties of an antibacterial composite resin loaded with fluoride-doped nano-zirconia fillers

EFFECT OF PREPARATION PARAMETERS ON ANTIBACTERIAL PERFORMANCE OF GEL COAT RESIN

A dental filling composite resin restorative with improved antibacterial function and hardness

Preparation of antimicrobial calcium phosphate/protamine composite powders with fluoride ions using octacalcium phosphate

Development of antibacterial dual-cure dental resin composites via tetrapod-shaped zinc oxide incorporation

Preparation of Machinable Polymer Composite with Sio2, Zro2 As Fillers for Prosthodontics

Mechanical and Antimicrobial Properties of Boron Nitride/Methacrylic Acid Quaternary Ammonium Composites Reinforced Dental Flowable Resins

Improving antibacterial performance of dental resin adhesive via co-incorporating fluoride and quaternary ammonium

Method for surface treatment of zirconia filler for improving performance of dental composite resin

Antibacterial properties of mesoporous silica coated with cerium oxide nanoparticles in dental resin composite

The Mechanical and Antibacterial Properties of Boron Nitride/Silver Nanocomposite Enhanced Polymethyl Methacrylate Resin for Application in Oral Denture Bases

Formulation and Characterization of New Experimental Dental Composites with Zirconium Filling in Different Forms

Spray-drying-assisted fabrication of CaF2/SiO2 nanoclusters for dental restorative composites

Novel core–shell CHX/ACP nanoparticles effectively improve the mechanical, antibacterial and remineralized properties of the dental resin composite

POSS hybrid bioactive glass dental composite resin materials: synthesis and analysis

The researchment of nami-material reinfoced dental composite resin

A Multifunctional Dental Resin Composite with Sr-N-Doped TiO2 and n-HA Fillers for Antibacterial and Mineralization Effects

Reinforcement of dental resin composite via zirconium hydroxide coating and phosphate ester monomer conditioning of nano-zirconia fillers.