Abstract:SUMMARYAn investigation of the anisotropic permeability of a carbon cloth gas diffusion layer (GDL) based on the integration of X‐ray micro‐tomography and lattice Boltzmann (LB) simulation is presented. The method involves the generation of a 3D digital model of a carbon cloth GDL as manufactured using X‐ray shadow images acquired through X‐ray micro‐tomography at a resolution of 1.74 µm. The resulting 3D model is then split into 21 volumes and integrated with a LB single‐phase numerical solver in order to predict three orthogonal permeability tensors when a pressure difference is prescribed in the through‐plane direction. The 21 regions exhibit porosity values in the range of 0.910–0.955, while the average fibre diameter is 4 µm. The results demonstrate that the simulated through‐plane permeability is about four times higher than the in‐plane permeability for the sample imaged and that the corresponding degrees of anisotropy for the two orthogonal off‐principal directions are 0.22 and 0.27. The results reveal that flow channelling can play an important role in gas transport through the GDL structure due to the non‐homogeneous porosity distribution through the material. The simulated results are also applied to generate a parametric coefficient for the Kozeny–Carman (KC) method of determining permeability. The current research reveals that by applying the X‐ray tomography and LB techniques in a complementary manner, there is a strong potential to gain a deeper understanding of the microscopic fluidic phenomenon in representative models of porous fuel cell structures and how this can influence macroscopic transport characteristics which govern fuel cell performance. Copyright © 2010 John Wiley & Sons, Ltd.

Determination Of Thickness And Air-Void Distribution Within The Iron Carbonate Layers Using X-Ray Computed Tomography

Research on the Interface Structure During Unidirectional Corrosion for Oil-Well Cement in H2S Based on Computed Tomography Technology

Three-dimensional Reconstruction and Porosity Calculation of Ceramic Coating: Nondestructive X-ray Computed Tomography

The Evolution of Pores in Thermal Barrier Coatings under Volcanic Ash Corrosion Using X-ray Computed Tomography

Anti-corrosion Characteristics of FeCO3 and Fe Ca Mg CO3 Scales on Carbon Steel in High-Pt CO2 Environments

Petrophysical Properties Analysis of a Carbonate Reservoir with Natural Fractures and Vugs Using X-ray Computed Tomography

Corrosion Damages of Reinforced Concrete Characterized by X-ray CT and DVC Techniques

Pore Structure Damages In Cement-Based Materials By Mercury Intrusion: A Non-Destructive Assessment By X-Ray Computed Tomography

Determination of the Anisotropic Permeability of a Carbon Cloth Gas Diffusion Layer Through X‐ray Computer Micro‐tomography and Single‐phase Lattice Boltzmann Simulation

Improvement on the CO2 corrosion prediction via considering the corrosion product performance

Application of X-CT Technology in the Microstructure Analysis of Cement-Based Materials

Investigation of the evolution of an iron carbonate layer and its effect on localized corrosion of X65 carbon steel in CO2 corrosion environments

Quantifying the influence of microstructure on the corrosion of Mg-Li alloys by using X-ray CT

Advanced Characterization of Three-Dimensional Pores in Coking Sand by Micro-Ct

Threshold Fine-Tuning and 3d Characterisation of Porous Media Using X-Ray Nanotomography

Study of Carbon Dioxide Corrosion Products by X-Ray Diffraction

Estimation of in-tube oil film thickness using electrical capacitance tomography

Moisture Penetration and Distribution Characterization of Hard Coal: a Μ-Ct Study

Quantitative image analysis on the filling proportion of corrosion products in reinforced concrete using X-ray computed tomography

3D characterization of closure of surface and internal fatigue cracks in nodular cast iron using Digital Volume Correlation of laboratory X-ray tomography images

Investigation of CO2 Diffusion in Oil-Saturated Porous Media by Using X-Ray Computer-Assisted Tomography