Abstract:To avoid the "susceptibility artifacts" in magnetic resonance imaging (MRI) and realize patient-specific medical devices with complicated shapes, a novel MRI compatible Zr-1Mo alloy with low porosity (c.a. 0.4%) were manufactured by laser powder bed fusion process(L-PBF) using gas-atomized Zr-1Mo(wt%) alloy powder. However, as-built Zr-1Mo(wt%) components using optimized process parameters show relatively high me-chanical performance(elongation of 6.4%, UTS of 1175 MPa), but contain 0.4 vol% defects which show a spherical morphology and distribute in the builds randomly. These defects definitely deteriorate the mechanical performance(especially ductility, fatigue behavior) of Zr-1Mo components manufactured by L-PBF. In order to eliminate defects in as-built Zr-1Mo components, hot isostatic pressing(HIP), which has been known as an effective process to decrease the porosity of additive manufactured products, was executed. Due to the elevated temperature and high pressure during HIP treatment, the randomly distributed defects were eliminated after the HIP process. Moreover, the alpha-martensite structure in the as-built alloy was transformed into a basketweave alpha + beta structure at low HIP temperature(1023 K and 1073 K) or lamellar alpha + beta structure at relatively high HIP temperature(1173 K and 1273 K). In the meantime, the elongation of HIP-treated Zr-1Mo components significantly increased, but the strength shows the opposite trend. From the viewpoint of mechanical property, Zr1Mo components HIP-treated at 1023 K possessed elongation of 19.9%, and UTS of 628 MPa should be optimized in this study. More importantly, porosity regrowth behavior was investigated to evaluate subsequent heat treatment feasibility for further improvement of mechanical performance. Due to intact raw material power as well as vacuum/low pressure inside the original defect caused by evaporation of metals, porosity regrowth can not be confirmed in HIP-treated Zr-1Mo components after subsequent heat treatment(holding temperature higher than the beta transus of Zr-1Mo alloy). Therefore, further improvement of mechanical performance by subsequent heat treatment for HIP-treated Zr-1Mo components is very promising and should conduct further research in the future

Combination of Hot Isostatic Pressing and Subsequent Heat Treatment for Additively Manufactured Zr-1Mo Components

Hot Isostatic Pressing of MRI Compatible Zr-1Mo Components Manufactured by Laser Powder Bed Fusion

Microstructure, Compressive Performance and Wear Resistance of Pure Molybdenum Additively Manufactured Via Laser Powder Bed Fusion

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Effect of Hot Isostatic Pressing on the Microstructure and Fracture Toughness of Laser Additive-Manufactured MoSiBTiC Multiphase Alloy

Influence of Annealing Treatment on the Microstructure, Mechanical Performance and Magnetic Susceptibility of Low Magnetic Zr–1Mo Parts Manufactured Via Laser Additive Manufacturing

Process-structure-property Modeling for Postbuild Heat Treatment of Powder Bed Fusion Ti-6Al-4V

Microstructure and Mechanical Properties of an Al–Mg–Si–Zr Alloy Processed by L-PBF and Subsequent Heat Treatments

Effects of Process Parameters on the Mechanical Properties of Additively Manufactured Zr-1Mo Alloy Builds.

Hot isostatic pressing of laser powder-bed-fused 304L stainless steel under different temperatures

Simultaneously improved the strength and ductility of laser powder bed fused Al-Cr-Fe-Ni-V high-entropy alloy by hot isostatic pressing: Microcrack closure and precipitation strengthening

Processing of High Interstitial Austenitic Steel with PBF‐LB/M‐Evolution of chemical inhomogeneity and microstructural features during Post‐Processing

Development of a high strength Zr/Sc/Hf-modified Al-Mn-Mg alloy using Laser Powder Bed Fusion: Design of a heterogeneous microstructure incorporating synergistic multiple strengthening mechanisms

Achieving Balanced Mechanical Properties in Laser Powder Bed Fusion Processed Inconel 718 Superalloy Through a Simplified Heat Treatment Process

Micro-mechanism and mechanical properties of solid-powder hot isostatic pressing diffusion-bonded Ti2AlNb alloy

Microstructural and mechanical optimization of selective laser melted Ti6Al4V lattices: Effect of hot isostatic pressing

Post-Heat Treatment Design of High-Strength Low-Alloy Steels Processed by Laser Powder Bed Fusion

The impact of heat treatment on microstructure, residual stress, and mechanical behavior of laser powder bed fusion additively manufactured Ti–6Al–2Sn–4Zr–2Mo alloy

Effects of Heat Treatments on the Microstructure and Tensile Properties of IN738 Superalloy with High Carbon Content Fabricated Via Laser Powder Bed Fusion

Effects of HIP Process Parameters on Microstructure and Mechanical Properties of Ti-6Al-4V Fabricated by SLM

Synergistic Improvement in Ductility and Hot Nitric Acid Corrosion Resistance of LPBF Ti-6Al-4V Alloy via Hot Isostatic Pressing