Abstract:I/II/III mixed mode fractures of intersecting joint fissures often occur in natural rock masses, and jointed rock masses are prone to rockbursts in deep underground engineering when subjected to long-term crustal stresses. However, most studies of the mechanical mechanisms of these intersected joints have been conducted by simplifying two-dimensional joint model tests. Furthermore, the fracture mechanisms of two-dimensional intersected joints under tension and compression are completely different from those of three-dimensional joints. This paper presents a novel prefabricated specimen with combinations of intersecting joints capable of detecting the failure behaviours of rock I/II/III mixed mode fractures under creep loading. Uniaxial compression and multistage creep tests are performed on prefabricated sandstone specimens with intersecting joints of 0°/0°, 0°/30°, 0°/60°, and 0°/90°. The experimental results show that with the increase in the number of prefabricated intersecting joints, the uniaxial compressive strength and elastic modulus values of the sandstone specimens gradually decrease. In addition, the sandstone specimens experience relatively few AE events and minor axial strain variations in the first creep stage and the second creep stage of the multistage creep test. The axial strain increases sharply due to the sharp increase in the number of AE events in the third creep stage. The 0°/60° sandstone specimen undergoes accelerated creep failure, resulting in mixed X-shaped tensile‒shear rupture. The RA value is high based on the quantification of the creeping cracks using the acoustic emission parameters of the rise angle (RA) and average frequency (AF). The AF values of the 0°/0°, 0°/30°, and 0°/90° sandstone specimens are high. The experimental results show that a larger joint intersection angle leads to greater mutual restraints and greater effects of prefabricated crack propagation in the rock specimens, thus increasing the final failure strength. Finally, based on the acoustic emission count, a characteristic variable D suitable for characterizing the creep damage evolution of a joint rock mass is established. The findings of this paper can facilitate an effective understanding of the creep effect of I/II/III mixed mode fracture and its micromechanism. The research results will have a certain reference value for the detection and risk mitigation of instantaneous and time-delayed rockbursts.

Experimental Study on the Fracture Evolution Process of Rock-like Specimens Containing a Closed Rough Joint Based on 3D-Printing Technology

Experimental and Numerical Investigation on Shear Failure Behavior of Rock-like Samples Containing Multiple Non-Persistent Joints

Method for Visualizing the Shear Process of Rock Joints Using 3D Laser Scanning and 3D Printing Techniques

Damage Evolution of Rocks Containing a Set of Cross-Joints Based on Acoustic Emission Characteristics

On Size Effect of Rock Joints Roughness Based on Varied Statistical Methods

Experimental study on instability failure of rock mass with rough joints under one-side constraint compression

Experimental and Numerical Studies on Mechanical Characteristics and Fracture Behaviours of Jointed Rock with Different Roughness

Experimental study of uniaxial compressive mechanical properties of rough jointed rock masses based on 3D printing

Strength test of 3D printed artificial rock mass with pre-existing fracture

Experimental Investigation into the Mechanical Behavior of Jointed Soft Rock Using Sand Powder 3D Printing

Study on mechanical and fracture characteristics of inclined weak-filled rough joint rock-like specimens

Mechanical and Volumetric Fracturing Behaviour of Three-Dimensional Printing Rock-like Samples Under Dynamic Loading

Influence of intermittent opening density on mechanical behavior and fracture characteristics of 3D-printed rock

Experimental and numerical modeling of deformation-cracking mechanics of 3D-printed rock samples with single fracture

An experimental study of mechanical behavior of brittle rock-like specimens with multi-non-persistent joints under uniaxial compression and damage analysis

Laboratory test and numerical simulations for 3D printed irregular columnar jointed rock masses under biaxial compression

Effect of fractures on mechanical behavior of sand powder 3D printing rock analogue under triaxial compression

Experimental study on I/II/III mixed mode fracture characteristics of a combined rock mass under creep loading

Natural joint effect on mechanical characteristics and fracture evolution of In-Site rocks under uniaxial compression

A Numerical Study of the Mechanical Behavior of Jointed Soft Rocks under Triaxial Loading Using a Bonded Particle Model

Study on Mechanical Model for Postpeak Shear Behavior of Rock Joints Based on Degradation Characteristics of the 3D Morphology