Abstract:Abstract The use of engineered wood products and mass timber panels such as cross laminated timber (CLT), glued laminated timber (glulam) and laminated veneer lumber (LVL) is becoming more common, as these products have benefits in terms of environmental credentials and resource utilisation and have the potential to provide faster and more economical construction processes. However, timber exposed to moisture for prolonged periods can degrade biologically, leading to a loss of appearance and decreased mechanical properties. Southern pine, radiata pine and shining gum timber are important forest resources for the Australian timber industry. To date, no in-depth studies on the hygroscopic properties of these species have been carried out from a timber wetting point of view. Consequently, existing literature has a knowledge gap regarding the determination of moisture movement properties in these species that are applicable to numerical modelling when used as solid wood or in the production of engineered wood products (EWPs). The work presented herein will help develop a better understanding of moisture ingress and egress in solid timber and EWPs and provide data for future predictive tools (such as numerical modelling) for moisture management in timber buildings. Samples were prepared from solid timber as well as EWP’s to examine the relationships between glue lines and edge gaps in CLT and multiple glue lines in LVL on moisture movement. As expected, longitudinal permeability was higher than radial and tangential permeability for the species tested. Southern pine samples had higher gas and liquid permeability values than radiata pine and shining gum. CLT with end grain sections including an edge gap had higher gas and liquid permeability than similar sections with glue lines only. LVL sections with 1 glue line had slightly lower permeability values than in samples with 2 glue lines. Gas and liquid permeabilities were lower for LVL samples than a two-layered veneer section without a glue line illustrating the barrier posed by the glue line. The moisture loss parameter during the diffusion testing was higher for LVL ends and CLT ends with edge gaps than face and edge sample sections. The results will be used to develop numerical models for moisture behaviour in solid and composite timber panels when exposed to humidity and free water. It is recommended to conduct additional studies to examine the impact of the adhesive layer and its properties on impeding moisture migration or functioning as a moisture barrier.

Calculating Moisture Emissivity of Timber Members with Different Surface Treatment

Theoretical and Experimental Study on Transient Measurement of Wood Thermal Properties

Response Surface Modeling Equilibrium Moisture Content of High Pressure Treated Paulownia Wood

The prediction of effective thermal conductivities perpendicular to the fibres of wood using a fractal model and an improved transient measurement technique

Experimental and Numerical Study of Moisture Distribution and Shrinkage Crack Propagation in Cross Section of Timber Members

Three-dimensional modeling of moisture transport in wood using near-infrared hyperspectral imaging and X-ray computed tomography in conjunction with finite element analysis

Experimental Measurements of Thermal Conductivity of Wood Species in China: Effects of Density, Temperature, and Moisture Content

Numerical investigations of dynamic moisture response to the climates inside wooden components in timber buildings and its potential threats

Prediction Distribution Model of Moisture Content in Laminated Wood Components

Micro-FTIR Spectroscopy and Partial Least-Squares Regression for Rapid Determination of Moisture Content of Nanogram-Scaled Heat-Treated Wood

Modeling moisture and heat transfer during superheated steam wood drying considering potential evaporation interface migration

Optimization of measurement and calculation methods for viscoelastic creep strain and mechanical adsorption creep strain during conventional drying process of Pinus sylvestris

Quantitative prediction of moisture content distribution in acetylated wood using near-infrared hyperspectral imaging

Evaluating moisture transfer properties of wood by inverse analysis of moisture content profiles determined during drying by X-ray attenuation

A mixed experimental–numerical electrical resistivity-based method for moisture content assessment in wood tested using the example of Douglas fir

Moisture changes and surface checking development during drying of Masson pine wood

Study of the hygroscopic properties of three Australian wood species used as solid wood and composite products

Mathematical Modeling of Moisture and Heat Transfer in Wood Particles During Convective Drying.

A new method for nondestructive evaluation of solid wood moisture content based on dual-energy X-ray absorptiometry

Thermal Responses of Woods Exposed to High Temperatures Considering Apparent Thermo-Physical Properties

Influence of materials and surface parameters on the moisture buffering in office buildings: A sensitivity analysis of China