Abstract:W-Ni alloy has been an important engineering material in military, nuclear industry and many other fields because of its excellent properties such as high strength and superior heat/corrosion/oxidation resistances. As a mainstream additive manufacturing technology based on powder-bed-fusion principle, selective laser melting (SLM) is suitable for the rapid fabrication of very complex W-Ni alloy components. However, researches on the powder densification behavior and microstructure formation mechanism of SLM W-Ni alloy are not thorough enough. In this work, a series of W-xNi (x = 16, 23, 30 wt.%) binary alloy samples were fabricated by SLM, using W/Ni mixed powders as the raw materials. The densification behaviors of the W/Ni mixed powders and the microstructure formation mechanisms of the different SLM W-Ni samples were studied. The results showed that when the W/Ni mixed powder bed was scanned by the laser, Ni powders with a relatively lower melting point would melt completely whereas W powders with a relatively higher melting point would rearrange themselves in the liquid Ni and only part of them could be dissolved into the liquid Ni. As the initial content of Ni powders increased, the rearrangement and dissolution of W powders proceed more sufficiently, thus leading to the improvement in densification degree. The relative densities of the W-16Ni, W-23Ni and W-30Ni SLM samples are 92.87 ± 0.67%, 98.66 ± 0.26% and 99.67 ± 0.18%, respectively. During the solidification processes of W-Ni molten pools, the precipitation of W grains from liquid Ni, the transformation of liquid Ni to γ-Ni solid solution and the precipitation of Ni2W from γ-Ni solid solution would occur in sequence. For the W-16Ni and W-23Ni samples, the grain morphology of the W precipitations is dendritic. For the W-30Ni samples, the W precipitations are globular. As a result of the unique melting- solidification behaviors, all the SLM samples possessed a tri-modal microstructure composed of unmelted W particles, dendritic/globular W grains, and γ-Ni solid solution with Ni2W intragranular precipitation. The average microhardness of the SLM W-Ni alloy samples decreased with the increase of Ni content, which could be explained by the variation in defect and microstructure features.

Cu-Ni-Sn Alloy Fabricated by Melt Spinning and Selective Laser Melting: a Comparative Study on the Microstructure and Formation Kinetics

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Evolution from Amorphous to Nanocrystalline and Corresponding Magnetic Properties of Fe-Si-B-Cu-Nb Alloys by Melt Spinning and Spark Plasma Sintering

Microstructures and mechanical properties of Si and Zr modified Al–Zn–Mg–Cu alloy-A comparison between selective laser melting and spark plasma sintering

Influence of Selective Laser Melting Process Parameters on Microstructure and Properties of a Typical Ni-Based Superalloy

Effect of Process Parameters on the Microstructure and Properties of Cu–Cr–Nb–Ti Alloy Manufactured by Selective Laser Melting

The mechanical and functional behaviors of Mn–15 wt.%Cu alloy produced by selective laser melting

Hierarchical microstructure and strengthening mechanism of Cu-36.8Fe alloy manufactured by selective laser melting

Selective laser melting of Cu–Cr–Zr copper alloy: Parameter optimization, microstructure and mechanical properties

Effect of laser power on microstructures and properties of Al-4.82Mg-0.75Sc-0.49Mn-0.28Zr alloy fabricated by selective laser melting

Microstructure, Phase Transformation and Mechanical Property of Ni-Co-Mn-In Alloy Prepared by Spark Plasma Sintering

Selective Laser Melting of Multi-Principal NiCrWFeTi Alloy: Processing, Microstructure and Performance

Effect of element evaporation on the microstructure and properties of CuZnAl shape memory alloys prepared by selective laser melting

Microstructure, Mechanical Properties, and Fatigue Fracture Characteristics of High-Fracture-Resistance Selective Laser Melting Al-Ni-Cu Alloys

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

Powder densification behavior and microstructure formation mechanism of W-Ni alloy processed by selective laser melting

Effect of nano-TiB2 particles on the anisotropy in an AlSi10Mg alloy processed by selective laser melting

Microstructure and Mechanical Behavior of TiCN Reinforced AlSi10Mg Composite Fabricated by Selective Laser Melting

Fabricating Homogeneous FeCoCrNi High-Entropy Alloys via SLM In Situ Alloying

Effect of Scanning Strategies on the Microstructure and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated through Selective Laser Melting

Nanoscale chemistry and atomic-scale microstructure of a bulk Ni3Sn material built using selective laser melting of elemental powder blends