Abstract:In order to verify the feasibility of three-dimensional (3D) printing technology in preparing the metamaterial absorbers with complex structure, a three-layer broadband absorbing metamaterial is designed and fabricated by 3D printing technology. The surface layer and middle layer of the metamaterial are composed of periodic arrays with different unit dimensions and the bottom layer of a slab structure. The optimized thickness of the metamaterial is 4.7 mm. A composite absorbent which consists of carbonyl iron powder and nylon is used to fabricate the absorber. In experiment, the obtained absorber is vertically irradiated by an electromagnetic (EM) wave. Two strong absorption peaks at 5.3 GHz and 14.1 GHz are achieved, with the reflection losses of -15.1 dB and -12.5 dB, respectively. The superposition of the two absorption peaks results in a reflection loss below -10 dB in a range from 4 to 18 GHz. The effective EM parameters of the surface layer and the middle layer are calculated by the S parameter inversion method. An effective model of the three-layer structure absorber is proposed and its reflectivity is calculated by using a multilayer structure reflectivity formula. The calculated reflectivity agrees well with the measured one. The absorbing and resonance mechanisms of the two absorption peaks are investigated by analyzing the dynamic distributions of power density loss, electric field and magnetic field. It can be clearly confirmed that the reflection losses at 5.3 GHz and 14.1 GHz are primarily concentrated on the bottom layer and surface layer, and the broadband absorption performance can be derived from the superposition of broadband absorptions of the three absorbing layers. Meanwhile, the strong electric coupling effect between the adjacent units in the surface layer is demonstrated by analyzing the electric-field distributions, which indicates that the strong reflection loss at 14.1 GHz is mainly caused by the electric response. The multiple scattering effects among the three layers are also considered according to the magnetic field distributions at two resonance frequencies. It is shown that there are two magnetic responses at 5.3 GHz and 14.1 GHz, respectively, and the multiple scattering contributes to increasing the EM wave propagation distance and enhancing the power loss. The designed absorbing metamaterials in this paper achieve good broadband absorption performances, particularly in the low frequency band. Combined with 3D printing rapid technology, a promising route to constructing 3D absorbing metamaterials with complex structures is proposed, which would be of great significance and broad practical prospect.

Wide-angle Microwave Absorption Properties of Multilayer Metamaterial Fabricated by 3D Printing

A Flexible Foldable Broadband Metamaterial Absorber Fabricated by Intaglio Printing Technology

A wide-angle broadband electromagnetic absorbing metastructure using 3D printing technology

An Ultra-Wideband and Translucent Metasurface Absorber Based on Water

Structural Broadband Absorbing Metamaterial Based on Three-Dimensional Printing Technology

Ultra-broadband Metamaterial Absorber with Graphene Composites Fabricated by 3D Printing

3D Printed Labyrinth Multiresonant Composite Metastructure for Broadband and Strong Microwave Absorption

3D Printed Propeller-Like Metamaterial for Wide-Angle and Broadband Microwave Absorption

Broadband Absorption Performance of 3D-Printed Polyetheretherketone-Based Electromagnetic Wave-Absorbing Composites

Asymmetric Three-Dimensional Metamaterial Absorber for Microwave Application

A Multi-Materials 3D-Printed Continuous Conductive Fibre-Based Metamaterial for Broadband Microwave Absorption

Design and Analysis of a Wideband Microwave Absorber Based on Graphene-Assisted Metamaterial

A High-performance Metamaterials Absorbing Structures Based on Fused Deposition Modeling

Ultrabroadband metastructure absorber with angular stability for conformal applications

Excellent microwave absorption property of 3D printed SiCN matrix metamaterial

Material–structure Integrated Design for Ultra-Broadband All-Dielectric Metamaterial Absorber

3D Printed Low-Permittivity All-Dielectric Metamaterial for Dual-Band Microwave Absorption Based on Surface Lattice Resonances

Design and Analysis of a Wideband and Wide Angle 3D Metamaterial Absorber

Three-Dimensional Printed Ultrabroadband Terahertz Metamaterial Absorbers

Multimaterial 3D-printing of graphene/Li0.35Zn0.3Fe2.35O4 and graphene/carbonyl iron composites with superior microwave absorption properties and adjustable bandwidth

Bioinspired 3D Printed Metamaterial for Wideband Microwave Absorption and Aerodynamic Efficiency