Abstract:TiAlSiN nanocomposite coatings were deposited in a closed field unbalanced magnetron sputtering system by reactive sputtering from Ti0.475Al0.475Si0.05 targets using modulated pulsed power magnetron sputtering (MPPMS) under a floating substrate bias. The ratio of the nitrogen flow rate to the total gas flow rate (fN2) was varied from 0 to 40%. The application of MPPMS as sputtering sources was aimed at generating a high ionization degree of the sputtered material and a high plasma density by using a pulsed high power approach. When fN2=0%, an amorphous-like structure Ti0.479Al0.454Si0.066 coating was deposited with a hardness of 10GPa. When nitrogen was added, an optimized nanocomposite structure of nc-TiAlN/a-Si3N4 formed in the TiAlSiN coating deposited at fN2=10%, in which 5–10nm TiAlN nanocrystallites were embedded in a 2–3nm thick amorphous Si3N4 matrix. As the fN2 was increased up to 40%, the elementary composition of the coatings remained almost the same, but the grain size of nanocrystallites approached to 10–20nm and the AlN phase gradually precipitated. A maximum hardness (H) of 33.2GPa, a hardness to the elastic modulus (E) ratio of 0.081 and an H3/E*2 ratio of 0.19GPa were found in the coating deposited at fN2=10%. The friction coefficient of the TiAlSiN coatings was around 0.8–0.9 as sliding against a Si3N4 counterpart under a normal load of 0.5N. A wear rate of 2.0×10−5mm3N−1m−1 was measured in the TiAlSiN coatings deposited at fN2=20–40%. As only a low residual stress is found in the TiAlSiN coatings, we consider the complete phase separation is responsible for the enhanced mechanical and tribological properties of the nc-TiAlN/a-Si3N4 nanocomposite coatings.

Effect of laser parameters on the mechanical properties of in situ synthesized TiN/Ti3Al composite coatings on Ti6Al4V

Synthesis of TiN/Ti3Al composite coatings on Ti6Al4V alloy by plasma spraying and laser nitriding

Effect of Processing Parameters on Microstructure of in Situ Synthesized TiN/Ti3Al Composite Coating

Effect of Laser Power on the Microstructure and Mechanical Properties of TiN/Ti 3 Al Composite Coatings on Ti6Al4V

In Situ Synthesis of Tin/Ti3al Intermetallic Matrix Composite Coatings on Ti6al4v Alloy

Microstructure and Wear Resistance of One-Step In-Situ Synthesized TiN/Al Composite Coatings on Ti6Al4V Alloy by a Laser Nitriding Process

Influence of Si Content on Microstructure and Mechanical Properties of TiAlSiN Nanocomposite Coatings

Effect of Nitrogen Protective Atmosphere on Microstructure and High Temperature Erosion Property of TiAl3 and Cr3C2 Composite Coatings

Effect of Laser Scanning Speed on TiN/TiB–Ti Based Composite

Microstructure and Tribological Properties of Laser Surface Alloyed TiN and TiC Reinforced Composite Coatings on TiAl Intermetallic Alloy

Effect of Heat Input on the Microstructure of In-Situ Synthesized TiN–TiB/Ti Based Composite Coating by Laser Cladding

Laser Rapid Preparation Tix Aly-TiN Composite Coating

Effect of Microstructure on Mechanical and Tribological Properties of Tialsin Nanocomposite Coatings Deposited by Modulated Pulsed Power Magnetron Sputtering

STUDY OF TiN/Ti COMPOSITE MATERIAL BY REACTIVE CO2 LASER DIRECT SYNTHESIS IN-SITU

Microstructure and Properties of Laser Surface Alloyed γ-NiCrAl/TiC/Cr7C3 Composite Coatings on γ-TiAl Intermetallic Alloy

Microstructure and tribological properties of laser in-situ synthesized Ti3Al composite coating on Ti-6Al-4V

Microstructure of laser clad TiC/NiAl–Ni3(Al,Ti,C) wear-resistant intermetallic matrix composite coatings

Effect of TiC Content on Ni/TiC Composites by Direct Laser Fabrication

Microstructure and Wear Resistance of a Laser Surface Alloyed γ-TiAl Intermetallic Alloy Ti-48Al-2Cr-2Nb

Effect of Al Content on Microstructure and Mechanical Properties of Ti–Al–Si–N Nanocomposite Coatings

The Influence of Processing Parameters on Laser Cladding Composite Coatings on TiAl Intermetallic Alloy