Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

Triimide-Functionalized n-Type Polymer Semiconductors Enabling All-Polymer Solar Cells with Power Conversion Efficiencies Approaching 9%

Mapping Nonfullerene Acceptors with a Novel Wide Bandgap Polymer for High Performance Polymer Solar Cells

Thiophene-Fused Perylenediimide-Based Polymer Acceptors for High-Performance All-Polymer Solar Cells

All-Polymer Solar Cells with Perylenediimide Polymer Acceptors

A Fluorinated Imide‐Functionalized Arene Enabling a Wide Bandgap Polymer Donor for Record‐Efficiency All‐Polymer Solar Cells

Novel polymer acceptors achieving 10.18% efficiency for all-polymer solar cells

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Fused perylene diimide-based polymeric acceptors with different π-conjugation and molecular conformation in all polymer solar cells

Terpolymer acceptors based on bithiophene imide for all-polymer solar cells

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Highly Efficient and Stable All-Polymer Solar Cells Enabled by Near-Infrared Isomerized Polymer Acceptors

All-polymer Solar Cells Based on Side-Chain-isolated Polythiophenes and Poly(perylene Diimide-Alt-dithienothiophene)

Effects of the Electron-Deficient Third Components in n-Type Terpolymers on Morphology and Performance of All-Polymer Solar Cells

High-Performance Polymer Solar Cells Based on A Wide-Bandgap Polymer Containing Pyrrolo[3,4-F]Benzotriazole-5,7-Dione with A Power Conversion Efficiency of 8.63%

Dithienocoronene Diimide Based Conjugated Polymers As Electron Acceptors for All-Polymer Solar Cells

Improvement in Power Conversion Efficiency of All-Polymer Solar Cells Enabled by Ultrafast Channels for Charge Dynamics

High-performance polymer solar cells based on terpolymer composed of one donor and two acceptors processed with non-halogenated solvent

Copolymers of perylene diimide with dithienothiophene and dithienopyrrole as electron-transport materials for all-polymer solar cells and field-effect transistors

Dithienoquinoxalineimide‐based Polymer Donor Enables All‐Polymer Solar Cells Over 19% Efficiency

8.30% Efficiency P3HT-based All-Polymer Solar Cells Enabled by a Miscible Polymer Acceptor with High Energy Levels and Efficient Electron Transport

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells