Abstract:Powered by the worldwide efforts of research groups experienced in dye‐sensitized, and thin‐film solar cells, perovskite solar cells (PSCs) reached a power conversion efficiency of 25.7% within 10 years. However, the presence of defects and trap density within the active layer's grain boundaries commonly operates as non‐radiative recombination centers. Hence, intensive efforts have been reported to passivate the inevitable bulk and interface defects of the active layer using additives or post‐treatment processing to enhance the efficiency and stability of PSCs. Herein, a facile post‐treatment strategy based on wet processing methylammonium lead triiodide, MAPbI3 (prepared from lead acetate and methylammonium iodide precursors) films with organic amine salts (FABr and FAI) is demonstrated. As a result, high‐quality films of mixed perovskites (FAxMA1‐xPbI3‐xBrx and FAxMA1‐xPbI3) were obtained. The surface treatment has efficiently passivate the defects in the host film, suppressing the non‐radiative carrier recombination. Compared to the control device, the increased open‐circuit voltage (from 0.5 V to 1 V) and fill factor (FF) values of the optimized device based on FAxMA1‐xPbI3 showed a PCE of 16.13%. And our findings revealed that post‐treatment is possible on wet perovskite film aged for a few minutes prior to its post‐treatment, which saved the energy used for pre‐annealing. Post‐treatment has been carried out on wet host film of (MAPbI3) aged for 3 minutes prior to its treatment. The host film, with evident pinholes was changed into smooth morphology and larger grain‐size mixed FAxM1‐xPbI3‐xBrx and FAxMA1‐xPbI3 films upon post‐treatment using FABr and FAI solutions respectively. Compared to the control device, the post‐treated devices had higher fill factor (FF) and a double rise in Open‐circuit voltage (VOC), leading to enhanced device efficiency. Our findings has also proved that post‐treatment is possible on wet films that saved the energy for pre‐annealing during post‐treatment.

Flash Surface Treatment of CH3NH3PbI3 Films Using 248 Nm KrF Excimer Laser Enhances the Performance of Perovskite Solar Cells

Defect Passivation in CH3NH3PbI3 Films Using Alkali Metal Fluoride Additives for Highly Efficient Perovskite Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Phase Engineering of Perovskite Materials for High-Efficiency Solar Cells: Rapid Conversion of CH3NH3PbI3 to Phase-Pure CH3NH3PbCl3 Via Hydrochloric Acid Vapor Annealing Post-Treatment

Enhanced performance of perovskite solar cells via laser-induced heat treatment on perovskite film

Enhancing perovskite solar cells efficiency through cesium fluoride mediated surface lead iodide modulation

4-Methoxy phenethylammonium halide salts for surface passivation of perovskite films towards efficient and stable solar cells

Laser fabricated carbon quantum dots in anti-solvent for highly efficient carbon-based perovskite solar cells

Surface Reconstruction Strategy Improves the All-Inorganic CsPbIBr2 Based Perovskite Solar Cells and Photodetectors Performance

Enhancing Perovskite Solar Cell Performance Through Femtosecond Laser Polishing

Enhanced Optoelectronic Quality of Perovskite Films with Excess CH3NH3I for High-Efficiency Solar Cells in Ambient Air

CH3NH3PbBr3 Quantum Dot-Induced Nucleation for High Performance Perovskite Light-Emitting Solar Cells.

Laser-assisted Crystallization of CH3NH3PbI3 Films for Efficient Perovskite Solar Cells with a High Open-Circuit Voltage.

Illumination Enhanced Crystallization and Defect Passivation for High Performance CsPbI3 Perovskite Solar Cells by Sacrificing Dye

Surface-activation Modified Perovskite Crystallization for Improving Photovoltaic Performance

Critical Role of Post-Treatment Induced Surface Reconstruction for High Performance Inorganic Tin-Lead Perovskite Solar Cells

Deciphering the Morphology Change and Performance Enhancement for Perovskite Solar Cells Induced by Surface Modification

Facile Face-Down Annealing Triggered Remarkable Texture Development in CH3NH3PbI3 Films for High-Performance Perovskite Solar Cells.

Grain‐Boundaries‐Engineering via Laser Manufactured La‐Doped BaSnO 3 Nanocrystals with Tailored Surface States Enabling Perovskite Solar Cells with Efficiency of 23.74%

Synergistic Interface Layer Optimization and Surface Passivation with Fluorocarbon Molecules toward Efficient and Stable Inverted Planar Perovskite Solar Cells

Single‐step post‐production treatment of lead acetate precursor‐based perovskite using alkylamine salts for reduced grain‐boundary related film defects