Abstract:Polycarbonate is a widely used ductile glassy polymer that can undergo large strain deformation before failure. During the plastic deformation process, some mechanical energy is converted to heat, which, if the specimen is loaded at rates sufficient that the heat cannot conduct out of the material, can result in significant temperature rises that affect the mechanical response. Typically, this is expected to result in a reduction in stress at large strain, compared to the behaviour under isothermal conditions; however, compared to other glassy polymers, it has been observed that less softening than expected is experienced in polycarbonate at high strain rates. The current paper describes a thorough investigation of temperature rises in polycarbonate. Compression experiments are performed using a screw-driven machine, a hydraulic machine, and a long split Hopkinson bar, all instrumented with a high-speed infrared camera to measure temperature rises at strain rates between 0.01 and 2600 s -1 at a starting temperature around 20°C. Further, temperature rises in compression experiments at 0.5 s -1 and starting temperatures between -80 to 150°C are measured using embedded thermocouples. These span the range of the secondary- to glass-transitions of polycarbonate, allowing investigation of the effect of these transitions. These experiments are supported by finite element simulations, which use a phenomenological viscoplastic model, to ensure the thermal boundary conditions are adiabatic. Temperature rises are observed in both temperature and rate-dependent tests: experiments at higher strain rates and lower temperatures experience a greater temperature rise because of the higher yield stress; however, there are differences in the conversion ratio between plastic work and heat (Taylor Quinney coefficient), which is both temperature and rate dependent, and strongly affected by both the secondary and glass transitions.

Thermal Degradation of Bisphenol A Polycarbonate by High‐resolution Thermogravimetry

Thermal Stability of Aromatic Polyesters Prepared from Diphenolic Acid and Its Esters

The Thermal Degradation of Bisphenol

The thermal degradation mechanism and kinetic analysis of hydrogenated bisphenol-A polycarbonate

Thermal Degradation Behavior and Flame Retardancy of Polycarbonate Containing Poly[(phenylsilsesquioxane)-co-(dimethylsiloxane)] and Potassium Diphenyl Sulfonate

Thermogravimetry of Thermoplastic Polyimide Powders under Four Different Atmospheres

Vapor-Induced Crystallization Behavior of Bisphenol-A Polycarbonate

Thermal Degradation Kinetics of Poly (vinyl chloride)

Degradation Behavior of Polycarbonate in Different Damp and Heat Natural Environments

Evaluation of the thermal degradation of PC/ABS/montmorillonite nanocomposites

Flame retarding mechanism of polycarbonate containing methylphenyl-silicone

Thermogravimetric Kinetic Analysis of PC/ABS/montmorillonite Nanocomposites

Thermal degradation of typical plastics under high heating rate conditions by TG-FTIR: Pyrolysis behaviors and kinetic analysis

Understanding the Thermal Degradation Mechanism of High-Temperature-Resistant Phthalonitrile Foam at Macroscopic and Molecular Levels

Kinetic Study of PVC Pyrolysis in Air by Thermogravimetric Analysis Using the Friedman Method

Comparison of the properties of bioderived polycarbonate and traditional bisphenol-A polycarbonate

Thermal degradation of polytetrafluoroethylene, modified polytetrafluoroethylene, and their nanocomposites with boron nitride nanobarbs: Lifetime predictions and kinetic analysis

Polytetrafluoroethylene decomposition in air and nitrogen

Thermomechanical coupling during large strain deformation of polycarbonate: Experimental study

Pyrolysis Kinetic Study and Reaction Mechanism of Epoxy Glass Fiber Reinforced Plastic by Thermogravimetric Analyzer (TG) and TG–FTIR (Fourier-Transform Infrared) Techniques

Emissions of PBDD/Fs, PCDD/Fs and PBDEs from flame-retarded high-impact polystyrene under thermal stress