Abstract:Flapping flight has undoubtedly played a significant role in many of the aeronautical engineering achievements in the past several centuries. Flapping motions of wings/fins are used by animals (such as birds, insects and bats) to generate lift or thrust to keep them aloft in the surrounding fluid. Researches in this area are not only motivated by the fundamental interest of understanding the mechanism of flapping flight, but also the development of Micro Air Vehicles (MAVs) based on biomimetics. In this lecture, we will address our efforts towards both experimental studies and virtual testing of flapping flight with our High End Digital Prototyping (HEDP) system. The aim of our research is to use physical and biological models to drive the engineering design of these vehicles. Firstly, two types of flapping-wing Unmanned Air Vehicles (UAVs) with spatial four-bar drive mechanism will be presented, including the wind tunnel experiment and prototype flight test results. Secondly, various computation approaches have been adopted to simulate the flapping motions, including traditional moving mesh techniques based on Arbitrary Lagrangian Eulerian (ALE) formulation, and Lattice Boltzmann method with immersed boundary methods. For a single wing-system, we have investigated the influences of various parameters on both the symmetric flapping and asymmetric flapping with bird-like or turtle-like flapping mode. For a tandem wing system, we have investigated the interaction between the hind wing and the vortex shedding off the fore wing and learned how to utilize the flow mechanism to achieve better aerodynamic performances. Moreover, Dynamic Mode Decomposition (DMD) algorithm has been adopted to reveal the underlying physics due to its capability and accuracy in analyzing the complex transient systems. Finally, the flight control design of a dragonfly-like Flapping Wing Micro Aerial Vehicle (FWMAV) is presented, which has incorporated a Linear-Quadratic Regulator (LQR) method and an Iterative Learning Tuning (ILT). In general, we expect that these virtual testing by computational simulations and flight control can drive the design of our next generation flapping-wing UAVs in the future.

Fabrication and characterization of IPMC actuated wing for flapping motion of butterfly

High Actuation Capability and Smooth-Deformation Piezo Morphing Wing Based on Multi-Layer Parallel Pre-Compressed MFC Bimorph

Towards Virtual Testing of Flapping Flight

Toward Practical Autonomous Flight Simulation for Flapping Wing Biomimetic Robots with Experimental Validation

Novel Computational Design of Polymer Micromachined Insect-Mimetic Wings for Flapping-Wing Nano Air Vehicles

Development of a Flapping Mechanism Inspired by the Flexible Wing-Base Structure of Insects for Wing Motion Control

The design and micromachining of an electromagnetic MEMS flapping-wing micro air vehicle

Design, Fabrication and Analysis of Microrobotic Insect Wings and Thorax with Different Materials by MEMS Technology

Artificial insect wings with biomimetic wing morphology and mechanical properties

Review on Ultra-Lightweight Flapping-Wing Nano Air Vehicles: Artificial Muscles, Flight Control Mechanism, and Biomimetic Wings

The Design and Microfabrication of A Sub 100 Mg Insect-Scale Flapping-Wing Robot

Design and Preparation of Biomorphic IPMC and Its Performance Research

Measurement of wing motion, deformation, and inertial forces of a biomimetic butterfly

Study on the Vibration Reduction Characteristics of FWMAV Flexible Bionic Wings Mimicking the Hindwings of Trypoxylus dichotomus

Design and Analysis of an Untethered Micro Flapping Robot Which Can Glide on the Water

Investigating the Mechanical Performance of Bionic Wings Based on the Flapping Kinematics of Beetle Hindwings

Monolithic Fabrication of an Insect-Scale Self-Lifting Flapping-Wing Robot

Design optimization and experimental study of a novel mechanism for a hover-able bionic flapping-wing micro air vehicle

Design and Fabrication of an SU-8 Biomimetic Flapping-wing Micro Air Vehicle by MEMS Technology

Design, Fabrication, and Analysis of Flapping and Folding Wing Mechanism for a Robotic Bird

Flapping Mechanism Design and Aerodynamic Analysis for the Flapping Wing Micro Air Vehicle