Abstract:Heavier-than-air flight at any scale is energetically expensive. This is greatly exacerbated at small scales and has so far presented an insurmountable obstacle for untethered flight in insect-sized (mass less than 500 milligrams and wingspan less than 5 centimetres) robots. These vehicles<a href="#ref-CR1">1</a>,<a href="#ref-CR2">2</a>,<a href="#ref-CR3">3</a>,<a href="/articles/s41586-019-1322-0#ref-CR4">4</a> thus need to fly tethered to an offboard power supply and signal generator owing to the challenges associated with integrating onboard electronics within a limited payload capacity. Here we address these challenges to demonstrate sustained untethered flight of an insect-sized flapping-wing microscale aerial vehicle. The 90-milligram vehicle uses four wings driven by two alumina-reinforced piezoelectric actuators to increase aerodynamic efficiency (by up to 29 per cent relative to similar two-wing vehicles<a href="/articles/s41586-019-1322-0#ref-CR5">5</a>) and achieve a peak lift-to-weight ratio of 4.1 to 1, demonstrating greater thrust per muscle mass than typical biological counterparts<a href="/articles/s41586-019-1322-0#ref-CR6">6</a>. The integrated system of the vehicle together with the electronics required for untethered flight (a photovoltaic array and a signal generator) weighs 259 milligrams, with an additional payload capacity allowing for additional onboard devices. Consuming only 110–120 milliwatts of power, the system matches the thrust efficiency of similarly sized insects such as bees<a href="/articles/s41586-019-1322-0#ref-CR7">7</a>. This insect-scale aerial vehicle is the lightest thus far to achieve sustained untethered flight (as opposed to impulsive jumping<a href="/articles/s41586-019-1322-0#ref-CR8">8</a> or liftoff<a href="/articles/s41586-019-1322-0#ref-CR9">9</a>).

Monolithic Fabrication of an Insect-Scale Self-Lifting Flapping-Wing Robot

The Design and Microfabrication of A Sub 100 Mg Insect-Scale Flapping-Wing Robot

Liftoff of an Electromagnetically Driven Insect-Inspired Flapping-Wing Robot

Review on Ultra-Lightweight Flapping-Wing Nano Air Vehicles: Artificial Muscles, Flight Control Mechanism, and Biomimetic Wings

Design, Fabrication and Analysis of Microrobotic Insect Wings and Thorax with Different Materials by MEMS Technology

The design and micromachining of an electromagnetic MEMS flapping-wing micro air vehicle

Design of the First Insect-scale Spinning-wing Robot

A Sub-100 mg Electromagnetically Driven Insect-inspired Flapping-wing Micro Robot Capable of Liftoff and Control Torques Modulation

Modular and Scalable Fabrication of Insect‐Scale Aerial Robots toward Demonstrating Swarm Flights

Design and Analysis of an Untethered Micro Flapping Robot Which Can Glide on the Water

Design of the first sub-milligram flapping wing aerial vehicle

A Modified Quasisteady Aerodynamic Model for a Sub-100 mg Insect-Inspired Flapping-Wing Robot

Fabrication and characterization of IPMC actuated wing for flapping motion of butterfly

Soft Molds with Micro-Machined Internal Skeletons Improve Robustness of Flapping-Wing Robots

Design and Fabrication of an SU-8 Biomimetic Flapping-wing Micro Air Vehicle by MEMS Technology

Development of a Flapping Mechanism Inspired by the Flexible Wing-Base Structure of Insects for Wing Motion Control

Design, takeoff and steering torques modulation of an 80-mg insect-scale flapping-wing robot

One-wing polymer micromachined transmission for insect-inspired flapping wing nano air vehicles

Untethered flight of an insect-sized flapping-wing microscale aerial vehicle

Experimental Optimization of Wing Lift for a Hummingbird-Like Micro Flapping-Wing Robot

Artificial insect wings with biomimetic wing morphology and mechanical properties