Abstract:A supervisory Model Predictive Control (MPC) approach is developed for an air path system for multi-mode operation in a diesel engine. MPC is a control method based on a predictive dynamic model of system and determines actuator control positions through the optimization of various factors such as tracking performances of target setpoints, moving speed of actuators, limits, etc. Previously, linear MPC has been successfully applied on the air path control problem of a diesel engine, however, most of these applications were developed for a single operation mode which has only one set of control target setpoint values. In reality, a single operation mode cannot cover all requirements of current diesel engines and this complicates practical implementations of linear MPC. The high priority targets for the development of diesel engines are low emissions, high thermal efficiency and robustness. These objectives require multi-mode operations such as a HP EGR (High pressure exhaust gas recirculation) mode in cold coolant condition, a Double EGR mode for sufficient EGR rates, a Diesel Particulate Filter (DPF) regeneration mode for the heat-up of exhaust gas temperature and a rich mode of exhaust gas for Lean NOx Trap (LNT) regeneration. Each engine operation mode requires different target setpoints from the air path, such as air mass flow rate and oxygen concentration. In the multi-mode operation, simple linearization based MPC is limited in the practical application because a linearization point changes depending on target setpoints of each operation mode. This means that a linear model for a specific operation mode is not valid in other operation modes, which have different target setpoints. Moreover, the modern diesel air path system is highly nonlinear and would require a significant number of linear models to adequately represent the entire behavior not only at all operation points of engine speed and load, but also at the various operation modes. In this study, a new scheme is proposed and tested on a diesel engine utilizing combined benefits of a supervisory MPC and component level nonlinear compensators. The developed nonlinear compensators are based on dynamic real-time inversions of individual component models. The control scheme comprises of three parts: a supervisory MPC as the coordination of target setpoints in high-level to achieve the objectives, a component level control of nonlinear compensator, state observation either by virtual sensor or by Electronic Control Unit (ECU) sensor. The test results from an engine test bench and a chassis dynamometer demonstrates that the proposed method works well in multi-mode operation and can be applied with the significant benefit that no mode specific control strategies and calibration are needed. A valuable benefit of this approach can be seen in the calibration effort, particularly during development when the setpoints are not necessarily fixed.

Control of Diesel Engines with Electrically Assisted Turbocharging Through an Extended State Observer Based Nonlinear MPC

Tuneable model predictive control of a turbocharged diesel engine with dual loop exhaust gas recirculation

A softly switched multiple Model Predictive Control of a turbocharged Diesel engine

Integrated Control of Torque and Emission of a Diesel Engine Based on LPV‐MPC

Multivariable Constrained Predictive Control and Its Application to A Commercial Turbofan Engine

Development of a Model Predictive Airpath Controller for a Diesel Engine on a High-Fidelity Engine Model with Transient Thermal Dynamics

Model Predictive Control of an Air Path System for Multi-Mode Operation in a Diesel Engine

Design of Disturbance Extended State Observer (D-ESO)-Based Constrained Full-State Model Predictive Controller for the Integrated Turbo-Shaft Engine/Rotor System

Tube-Based Model Predictive Control for Aero-Engine Transient-State Tracking Problems

Torque Tracking Control of Turbocharged Gasoline Engine Using Nonlinear MPC.

Design of Model Predictive Controller for Commercial Turbofan Engine

Nonlinear Model Predictive Controller Design Based on Learning Model for Turbocharged Gasoline Engine of Passenger Vehicle

Decoupling Control of Diesel Engine Air System Based on Multi-variable Extended State Observer

On Boost Pressure Control Of Diesel Engines With Double-Layer Passage Turbocharger

Nonlinear Model Predictive Control of Integrated Diesel Engine and Selective Catalytic Reduction System for Simultaneous Fuel Economy Improvement and Emissions Reduction

An adaptive model predictive controller for turbofan engines

Decoupled, Disturbance Rejection Control for A Turbocharged Diesel Engine with Dual-loop EGR System

An adaptive synergetic controller applied to heavy-duty gas turbine unit

Hierarchical multi-time-scale predictive thermal management and fuel optimization for heavy-duty compression ignition engines

An Assessment of Performance Trade-Offs in Diesel Engines Equipped with Regenerative Electrically Assisted Turbochargers

Holistic Diesel Engine and Exhaust After-Treatment Model Predictive Control