Abstract:Grinding is one of the most complex and accurate machining processes, and the efficiency of the grinding wheel depends significantly on its surface properties. This work aims to propose an algorithmic manner that reduces the cost and time to conduct grinding of an optimized DIN 1.2080 tool steel (SPK) using a soft computing technique to obtain the best combination of input parameters including depth of cut (20, 40, 60 μm), wheel speed (15, 20, 25 m/s), feed rate (100, 300, 500 mm/s), and incidence angle (0, 30, 45 de grees) with respect to output parameters consisting of average surface roughness and specific grinding energy. According to the input parameters and their levels, an experiment using fractional factorial design of experiment (RFDOE) was designed. Later on, two parallel feed-forward backpropagation (FFBPNN) networks with similar topology made up of 4, 11, and 1 units in their input, hidden, and output layers are trained, respectively. After sensitivity analyses of networks for determination of the relative importance of input variables, a genetic algorithm (GA) adopting linear programming (LP) based on Euclidean distance is coupled to networks to seek out the best combinations of input parameters that result in minimum average surface roughness and minimum specific grinding energy. The findings revealed that RFDOE provides valid data for training FFBP networks with a total goodness value of more than 1.99 in both cases. The sensitivity analyses showed that feed rate (38.97%) and incidence angle (33.94%) contribute the most in the case of average surface roughness and specific grinding energy networks, respectively. Despite the similar surface quality based on scanning electron microscopy (SEM), the optimization resulted in an optimized condition of the depth of cut of 25.23 μm, wheel speed of 15.02 mm/s, feed rate of 369.45 mm/s, and incidence angle of 44.98 de grees, which had a lower cost value (0.0146) than the optimum one (0.0953). Thus, this study highlights that RFDOE with a hybrid optimization using FFBP networks-GA/LP can effectively minimize both average surface roughness and specific grinding energy of SPK.

Improvement of Cutting Force and Material Removal Rate for Disc Milling TC17 Blisk Tunnels Using GRA–RBF–PSO Method

Integrated multi-objective optimization on the geometrical design of a disk-type milling cutter with multiple inserts applying uniform design, RBF neural network, and PSO algorithm

Research on Grinding Force Prediction of Flexible Abrasive Disc Grinding Process of TC17 Titanium Alloy

Pareto Fronts of Machining Parameters for Trade-off among Energy Consumption, Cutting Force and Processing Time

Multi-response optimization in face milling of EN-31 steel using analytical hierarchy process-based GRA

Optimization of Grinding Parameters of Tool Steel by the Soft Computing Technique

Tool Orientation Optimization for Disk Milling Process Based on Torque Balance Method

A combination of PSO-ANN hybrid algorithm and genetic algorithm to optimize technological parameters during milling 2017A alloy

A New Approach of Modelling Bottom Edge Cutting in 4-Axis Rough Milling of Complex Parts and Its Application on Feed Rate Optimization

Optimized Material Removal and Tool Wear Rates in Milling API 5ST TS-90 Alloy: AI-Driven Optimization and Modelling with ANN, ANFIS, and RSM

Development of a hybrid particle swarm optimization algorithm for multi-pass roller grinding process optimization

Modeling and Optimization of High-Grade Compacted Graphite Iron Milling Force and Surface Roughness Via Response Surface Methodology

Multi-response optimization of carbon fiber reinforced polymer (CFRP) drilling using back propagation neural network-particle swarm optimization (BPNN-PSO)

Understanding Machining Process Parameters and Optimization of High-Speed Turning of NiTi SMA Using Response Surface Method (RSM) and Genetic Algorithm (GA)

Multi-Objective Optimization of Micro-Milling Titanium Alloy Ti-3Al-2.5V (Grade 9) Using Taguchi-Grey Relation Integrated Approach

Optimization of grinding process parameters based on BILSTM network and chaos sparrow search algorithm

Multi-algorithm fusion–based intelligent decision-making method for robotic belt grinding process parameters

Estimation of tool wear and optimization of cutting parameters based on novel ANFIS-PSO method toward intelligent machining

Characterization of MHC class II‐presented peptides generated from an antigen targeted to different endocytic compartments

Optimization of Cutter Geometric Parameters in End Milling of Titanium Alloy Using the Grey-Taguchi Method

Analysis and Optimization of the Milling Performance of an Industry-Scale VSM via Numerical Simulations