Abstract:Cu matrix composites have received increased attention in a wide industrial area because of their excellent mechanical properties and good electrical and thermal conductivity. However, the addition of general ceramic reinforcements often leads to a marked reduction in electrical conductivity for Cu matrix composites. In this study, the ZrB 2 -reinforced Cu composites have been developed to overcome this drawback since these metal borides possess relatively high electrical conductivity. The 5 wt.% ZrB 2 /Cu composites were prepared using hot-pressed sintering techniques at varying temperatures from 760 to 920°C. The influence of sintering temperature on the microstructure, relative density, and mechanical and electrical properties was examined. The results of the SEM observation show that ZrB 2 particles are seamlessly integrated into the Cu matrix for all ZrB 2 /Cu composites. The average grain size of the Cu matrix increases from 360 to 980 nm with the increase of the sintering temperature. The increase in sintering temperature also leads to the surface porosity decrease from 1.4 to 0.4%. The relative density and electric conductivity of the composites increase at the same time as the sintering temperature increases. However, microhardness increases and decreases, with a maximum value of 92 HV0.2 achieved at 840°C. The elastic modulus and nanohardness maps determined from the nanoindentation indicate that the reinforced ZrB 2 particles demonstrate the highest values for elastic modulus (340–500 GPa) and nanohardness (30–48 GPa). At the same time, the Cu matrix possesses a modulus of 100–200 GPa and nanohardness of about 10 GPa. TEM observation confirmed that the sintering temperature exhibits little influence on the interface reaction between ZrB 2 and Cu. Both sharp interface and interface with amorphous transition layer are observed. The variation of microhardness is mainly due to the strengthening of grain refinement and to the mismatch of the thermal expansion coefficients. The above results can provide further insights into the deeper understanding of the role of sintering temperature during hot-pressed sintering.

Effect of Sintering Temperature on Properties and Microstructure of W-40vol%ZrC

Influence of Zrc Content on the Elevated Temperature Tensile Properties of Zrcp/W Composites

Effect of Zrc Content on Microstructure and Properties of Tungsten Materials

Microstructure Evolution and Properties of Tungsten Reinforced by Additions of ZrC

Effect of Sparking Plasma Sintering Temperature on the Microstructure and Properties of Ultra-fine Crystalline W-40Cu Composites

Effect of sintering temperature and holding time on the microstructure and mechanical properties of ZrB2–SiCw composites

Effect of Sintering Temperature on the Microstructure and Properties of High-Strength and Highly Conductive 5 wt.% ZrB2/Cu Composite

Densification and microstructure evolution of W-TiC-Y2O3 during spark plasma sintering

Microstructure and Characterization of Wc-2.8 Wt% Al2o3-6.8 Wt% Zro2 Composites Produced by Spark Plasma Sintering

Effect of ZrC nano-powder addition on the microstructure and mechanical properties of binderless tungsten carbide fabricated by spark plasma sintering

Toughening Mechanisms and Interfacial Bonding of W-ZrC Composites

Processing of ZrB2-15wt%Cu Composites Via Spark Plasma Sintering

Effect of Heat Treatment on Microstructure and Mechanical Properties of ZrC Particles Reinforced Tungsten-Matrix Composites

Low temperature sintering of ZrC-SiC composite

Study on ZrB2-SiC Prepared by Field Assisted Sintering

Mechanical and Thermal Properties of ZrC/ZTA Composites Prepared by Spark Plasma Sintering

THE INFLUENCE OF ZrC PARTICLE CONTENT ON THE MECHANICAL PROPERTIES OF TUNGSTEN MATRIX COMPOSITES

Effect of sintering temperature on densification of ultra-high temperature ceramic ZrB2-SiC

Processing and Mechanical Properties of Zirconium Diboride‐Based Ceramics Prepared by Spark Plasma Sintering

Effect of Ti Additives on the Sintering Behavior and Mechanical Properties of ZrC-W Composites

Effect of Iron Additive on the Sintering Behavior of Hot-Pressed ZrC-W Composites