Abstract:Objectives: This study aims to investigate bond strength between zirconia and resin cement through surface treatments with Er: YAG laser, Nd: YAG laser, and Si-Zr coating. Methods: Seventy-five round pre-sintered zirconia discs with a diameter of 18 mm and a thickness of 1.5 mm were prepared by a powder compactor. Fifty discs were randomly divided into five groups of 10 discs each and were subjected to five surface treatments: no treatment (control group), sandblasting with alumina particles (sandblasting group), Er: YAG laser treatment (Er: YAG laser group), Nd:YAG laser treatment (Nd: YAG laser group), and Si-Zr coating treatment (Si-Zr coating group). The discs were then bonded to composite resin columns with resin cement. The shear bond strength of each group was tested with a universal tester. Roughness tester, scanning electron microscope (SEM), and energy dispersive spectroscopy were used to analyze surface performance. Results: The bond strength of the Si-Zr coating group was higher than that of the remaining groups (P<0.05). The difference in bond strength between the sandblasting group and the Er: YAG laser group was not statistically significant (P>0.05), but both of them had higher bond strength than the Nd: YAG laser group (P<0.05). The Si-Zr coating group had the highest surface roughness (P<0.05). The surface roughness of the sandblasting, Er: YAG laser, and Nd: YAG laser groups was higher than that of the control group (P<0.05), but the difference among the three groups was not statistically significant (P>0.05). SEM observations showed irregular scratches on the surface of the sandblasting group and large pits with holes on the surface of the Er: YAG and Nd: YAG laser groups. In the Er: YAG laser group, the crystal structure was replaced by a smooth surface with a large amount of microcracks due to partial melting. Complex porous structures that comprised "island-like" structures and mass pores among the grains were observed on the surface of the Si-Zr coating. Only Zr, O, and Y were detected on the surfaces of the control, Er: YAG laser, and Nd: YAG laser groups. Al was found on the surface of the sandblasted group, and a higher proportion of Si was detected on the surface of the Si-Zr coating group. Conclusions: Er: YAG laser and Nd: YAG laser treatment on the zirconia ceramic surface could increase roughness and improve the bond strength to resin cement. Si-Zr coating treatment is an effective alternative for increasing the roughness and bond strength of zirconia surface and is superior to sandblasting and laser treatments.

Characteristics of Different Veneering Porcelain Adhesion to Zirconia Cores

Bonding Strength Between Zirconia Core and Different Veneering Ceramics

Shear Bond Strength of Ceramic Veneers to Zirconia–Calcium Silicate Cores

The effect of adhesive surface with porcelain sintering and two silane coupling agents on the adhesive properties of zirconia

Effect of different treatments of highly translucent zirconia on the bonding strength between zirconia and veneering porcelain

Effect of various intermediate ceramic layers on the interfacial stability of zirconia core and veneering ceramics

Synergistic Reinforcement of Surface Modification on Improving the Bonding of Veneering Ceramics to Zirconia

Bonding of Novel Self-Glazed Zirconia Dental Ceramics

Evaluation of bond strength between zirconia milled ceramic material and veneered dental porcelain

Evaluation of the Bonding Shear Strength between Enamel and Dentin Feldspathic Porcelain and Two Different Monolithic Zirconia with Low and High Translucency

The effect of graded glass-zirconia structure on the bond between core and veneer in layered zirconia restorations

[Research on Bond Durability among Different Core Materials and Zirconia Ceramic Cemented by Self-Adhesive Resin Cements].

Exploring Zirconia Adhesion: Pre and Postsintering Physical Surface Treatment, Chemical Treatment, and Cement Interactions

[Study on the Compatibility of Yttria-Stabilized Zirconia Framework Bonded to the Corresponding Veneering Ceramic].

The Shear Bond Strength of Resin-Based Luting Cement to Zirconia Ceramics after Different Surface Treatments

Long-term Bond Strength between Layering Indirect Composite Material and Zirconia Coated with Silicabased Ceramics

In vitro short-term bonding performance of zirconia treated with hot acid etching and primer conditioning

A new surface treatment method: fusing glass ceramic to zirconia

Influence of Different Surface Treatments on Zirconia/resin Shear Bond Strength Using One-Bottle Universal Adhesive

Effect of laser and coating surface treatment on the bond strength of zirconia ceramics

The research on the bond durability between self -adhesive cements and zirconia ceramic