Abstract:Nickel-based superalloy is mainly used for fabricating the important high temperature parts including the turbine disk, turbine baffle, compressor disk, and other critical components. Ceramic inclusions in powder metallurgy (PM) superalloy could promote fatigue crack initiation, and thus accelerating the crack propagation under certain conditions. In this case, the ultra-clean nickel-based superalloy powder is critical for PM superalloy components. Generally, there are two well-known methods of fabricating superalloy powders, i.e., argon gas atomization (AA) and plasma rotating electrode process (PREP). Electrode induction melting gas atomization (EIGA) process is a newly developed method of preparing ultra-clean metal powders. The EIGA process is a completely crucible-free melting and atomization process developed by ALD vacuum technologies. In this process, a slowly rotating prealloyed bar is fed into a conical induction coil. The end of the bar is inductively heated and molten alloys falls into an atomizer where the liquid alloy is atomized with a high-pressure inert gas. The EIGA prepared powders possess the advantages of AA (more fine powders) and PREP (ultra-clean powders) processes. Generally, there are two key issues in EIGA process, and the free-fall gas atomizer design is one of the critical issues for the powder yield and quality. Free-fall gas atomizers are some of the first two fluid atomizer designs to be used for molten metal atomization. In a simple open (unconfined stream) design a melt stream falls from a tundish exit via gravity into the convergence of focused atomization gas jets where it is disintegrated. The gas-melt interaction is complex, and it is difficult to characterize the interaction process directly. To have a good understanding of the atomisation technology, the physical break-up process instead of correlating the gas dynamics with droplet fragmentation indirectly must be able to be examined. And it will be desirable, if we input the atomization parameters, we can obtain the particles' distributions directly. In this work, a computational fluid dynamic approach to simulating the primary and secondary atomization processes is developed by using the volume of fluid method and discrete phase model. By integrating the metal stream break-up (in primary atomization) with the flow field and particles distribution simulation (in second atomization), this numerical simulation method is able to provide the direct assessment for the atomisation process. To verify the method performance, the melt stream is initialized into a 4 mm-diameter stream, which is then injected into the gas flow field for further fragmentation. The experimental results show that the simulated particles' diameter distribution is consistent with the experimental results in the same conditions.

Study on Powder Characteristics and Effect Factors of Droplets Size During Electrode Induction Melting Gas Atomization

Nucleation on Thermal History and Microstructural Evolution of Atomized Ti-48Al Nano and Micro-Powders

Size Dependent Phase Transformation in Atomized TiAl Powders

Effect of Electrode Induction Melting Gas Atomization Process on Fine Powder Yields: Diameter of Free-Fall Gas Atomizer

Computational Fluid Dynamic Investigation of the Primary and Secondary Atomization of the Free-Fall Atomizer in Electrode Induction Melting Gas Atomization Process

Size-dependent Microstructure Evolution and Formation Mechanisms During the Gas Atomization Process of FGH4113A Ni-based Superalloy Powder

The Influence of Cooling Rate on the Microstructure and Phase Fraction of Gas Atomized NiAl3 Alloy Powders During Rapid Solidification

Impact of Atomization Pressure on the Particle Size of Nickel-Based Superalloy Powders by Numerical Simulation

Effect of Electrode Induction Melting Gas Atomization on Powder Quality: Satellite Formation Mechanism and Pressure.

Effects of gas pressure and catheter length on the breakup of discontinuous NiTi droplets in electrode induction melting gas atomization

Comparative Study of Nickel-Based Super-Alloy Powders Atomized by Argon and Nitrogen

Low-pressure argon atomization process of 7055Al alloy powders

Microstructural Evolution of Al–Ni–Y Powders with Different Sizes

Particle Size Dependence of the Microsegregation and Microstructure in the Atomized Ni-based Superalloy Powders: Theoretical and Experimental Study

Consecutive Induction Melting of Nickel-Based Superalloy in Electrode Induction Gas Atomization

Properties and Characterization of Ti-6Al-4V Alloy Fine Powders Prepared by Electrode Induction Melting Gas Atomization (EIGA) Technique

Effect of Electrode Induction Melting Gas Atomization Process on Fine Powder Yields: Continuous Metal Melt Flow

Characterization of pre-alloyed NiTi powders produced by electrode induction-melting inert gas atomization for additive manufacturing

Characteristics of 7055Al alloy powders manufactured by gas-solid two-phase atomization: A comparison with gas atomization process

Analysis of Porosities in Nickel-Based Superalloys Powders

Preparation of Ti6Al4V Powder with High Yield of Fine Particle by Crucible-less Gas Atomization Technology