Abstract:Drying is a very important unit operation in many industries such as food, pharmaceuticals, chemicals and ceramics. In most cases, wet materials are dried by forced convection using hot air flow. Heat and mass transfer processes during drying have been studied by both experimental and numerical simulation methods. For the purpose of studying the mechanism of heat and mass transfer and stress-strain distribution during the hot air drying of biological porous medium, two-way coupled thermo-hydro-mechanical mathematical model has been developed to simulate the hot air convective drying process of biological porous media on basis of Fickian diffusion theory, Fourier’s law of heat conduction and thermoelasticity mechanics. The following assumptions were made in order to find a solution to the hot air drying model: the biological porous medium was homogeneous and isotropic; the deformation during drying was elastic. The transient model, composed of a system of partial differential equations, was solved by finite difference methods. The computational procedure was programmed using C language. Some physical and mechanical properties of carrot changing with dry basis moisture content and temperature were considered. The numerical results were compared with available experimental data obtained during the drying of potatoes and carrots. The relative errors between numerical results and experimental data were both less than 5%, which showed the numerical results obtained using the mathematical model were in good agreement with the experimental data. Numerical simulations of the drying curve variations and the spatio-temporal distributions of moisture, temperature and drying stresses and strains of carrot were also evaluated. The temperature and moisture content showed a gradient inside carrot slice during drying. As the drying process proceeded, the temperature inside the carrot slice initially increased to reach the wet bulb temperature of the environment and eventually leveled off. The dry basis moisture content inside the carrot slice decreased, with the fastest decreased at the heat and mass transfer interface, eventually reached the equilibrium moisture content of the potato and leveling off. Both the moisture content gradient and the temperature gradient decreased gradually in the thickness direction. The normal stress was negative in all parts of the carrot slice, and the larger the closer to the evaporation interface. The shear stress was positive in all parts of the carrot slice, and the maximum shear stress occurred in the middle of the carrot slice. As in the case of the normal stress, the values of the normal strain were negative. The change trend of normal strain with time was consistent with that of moisture content. These results indicated that the observed physical deformations were caused by the dehydration of carrot slice during drying. The influence of drying conditions, such as air temperature, air velocity and the thickness of porous media on drying process was analyzed. Analysis showed that under certain drying conditions, the higher air temperature, the greater air velocity and the thinner slice thickness, the shorter drying time. This work should help in developing an understanding of the relationship between mass and heat transfer, shrinkage, stress, strains and physical degradation.

Numerical Simulation Of Water Absorption And Swelling In Dehulled Barley Grains During Canned Porridge Cooking

An Easily Implemented Agro-Hydrological Procedure with Dynamic Root Simulation for Water Transfer in the Crop–soil System: Validation and Application

Dumpling Cooking - Modeling and Simulation

Modelling the physical properties change of canned glutinous rice porridge during cooking

Measurement and Modelling of Moisture Distribution and Water Binding Energy of Dredged Sludge

Numerical study of heat and mass transfer during drying process of barley grain piles based on the pore scale

Modeling Simultaneous Heat and Mass Transfer for Microwave Drying on Apple

Modeling Equilibrium Moisture Content of Brown Rice As Affected by High-Pressure Processing

Mass-Transfer Simulation Software Study of Sliced Porous Production During Convection Drying Process

Computer simulation of temperature changes in a wheat storage bin

A fully coupled multiphase model for infrared-convective drying of sweet potato

Continuous modeling of superheated steam drying of single rice grains

Modeling and Simulation of Swelling Behavior of Thermosensitive Hydrogels

Simulation of Dynamic Root Growth and Water Transfer in Soil-Crop-atmosphere System

Numerical Study to Predict Temperature and Moisture Profiles in Unventilated Grain Silos at Prolonged Time Periods

Simulation and experimental study of heat-moisture-solute transfer during drying process of porous media

Analytical and numerical solutions of pore formation in elastic food materials during dehydration

Mathematical Model and Numerical Simulation of Biological Porous Medium During Hot Air Drying

Modelling of convective drying of potatoes polyhedrons

Simulation of Water Cycling in Wheat-maize Field in North China

Measurements and Analysis of the Physical Properties of Cereal Seeds Depending on Their Moisture Content to Improve the Accuracy of DEM Simulation