Abstract:A detailed understanding of the cell adhesion on polymeric surfaces is required to improve the performance of biomaterials. Quartz crystal microbalance with dissipation (QCM-D) as a surface-sensitive technique has the advantage of label-free and real-time monitoring of the cell-polymer interface, providing distinct signal patterns for cell-polymer interactions. In this study, QCM-D was used to monitor human fetal osteoblastic (hFOB) cell adhesion onto polycaprolactone (PCL) and chitosan (CH) homopolymer films as well as their blend films (75:25 and 25:75). Complementary cell culture assays were performed to verify the findings of QCM-D. The thin polymer films were successfully prepared by spin-coating, and relevant properties, i.e., surface morphology, ζ-potential, wettability, film swelling, and fibrinogen adsorption, were characterized. The adsorbed amount of fibrinogen decreased with an increasing percentage of chitosan in the films, which predominantly showed an inverse correlation with surface hydrophilicity. Similarly, the initial cell sedimentation after 1 h resulted in lesser cell deposition as the chitosan ratio increased in the film. Furthermore, the QCM-D signal patterns, which were measured on the homopolymer and blend films during the first 18 h of cell adhesion, also showed an influence of the different interfacial properties. Cells fully spread on pure PCL films and had elongated morphologies as monitored by fluorescence microscopy and scanning electron microscopy (SEM). Corresponding QCM-D signals showed the highest frequency drop and the highest dissipation. Blend films supported cell adhesion but with lower dissipation values than for the PCL film. This could be the result of a higher rigidity of the cell-blend interface because the cells do not pass to the next stages of spreading after secretion of their extracellular matrix (ECM) proteins. Variations in the QCM-D data, which were obtained at the blend films, could be attributed to differences in the morphology of the films. Pure chitosan films showed limited cell adhesion accompanied by low frequency drop and low dissipation.

Interaction of fibroblast cells onto chloric acid-treated poly(alpha-hydroxy acid) polymer surfaces

Interaction of human chondrocytes and NIH/3T3 fibroblasts on chloric acid-treated biodegradable polymer surfaces.

Effect of Poly(3-Hydroxybutyrate-co-3-hydroxyvalerate) Surface with Different Wettability on Fibroblast Behavior

Surface Modification of Poly(tetrafluoroethylene) Films Via Plasma Treatment and Graft Copolymerization of Acrylic Acid

Surface Functionalization of Polycaprolactone Films Via Surface-Initiated Atom Transfer Radical Polymerization for Covalently Coupling Cell-Adhesive Biomolecules.

Methacrylate polymer layers bearing poly(ethylene oxide) and phosphorylcholine side chains as non-fouling surfaces: in vitro interactions with plasma proteins and platelets.

Effect of lipase treatment on the biocompatibility of microbial polyhydroxyalkanoates

Preparation and Cell Affinity Evaluation of Polylactide Film with Micro-Patterned Surface

Surface Modification of Polycaprolactone Membrane Via Aminolysis and Biomacromolecule Immobilization for Promoting Cytocompatibility of Human Endothelial Cells.

Surface modification of polycaprolactone nanofibers through hydrolysis and aminolysis: a comparative study on structural characteristics, mechanical properties, and cellular performance

Characterization of surface property of poly(lactide-co-glycolide) after oxygen plasma treatment.

Effects of surface modification of poly (3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) on physicochemical properties and on interactions with MC3T3-E1 cells.

Monitoring Cell Adhesion on Polycaprolactone-Chitosan Films with Varying Blend Ratios by Quartz Crystal Microbalance with Dissipation

Surface Modification of Poly-L-Lactic Acid (plla) Membrane by Grafting Acrylamide: an Effective Way to Improve Cytocompatibility for Chondrocytes

Layer-by-layer Assembly to Modify Poly(l-Lactic Acid) Surface Toward Improving Its Cytocompatibility to Human Endothelial Cells.

Effect of surface treatment on the biocompatibility of microbial polyhydroxyalkanoates.

Preparation of Hydrophilic Poly(L-Lactide) Electrospun Fibrous Scaffolds Modified with Chitosan for Enhanced Cell Biocompatibility

Adhesion and Proliferation of Osteoblast on the Amidation Surface of Polylactide Film

Surface engineering of poly(dl-lactic acid) by entrapment of alginate-amino acid derivatives for promotion of chondrogenesis

Acetic-Acid Plasma-Polymerization on Polymeric Substrates for Biomedical Application

Hydrophilicity Improvement of Polyhydroxyalkanoate Films