Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effect of Temperature on the Chemical Composition and Physicochemical Properties of Diester Aviation Lubrication Oil

The Deterioration Mechanism of Diester Aero Lubricating Oil at High Temperature

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Oxidative degradation of synthetic ester and its influence on tribological behavior

Research Progress of Lubricant Oxide Films in a Wide Temperature Range

Tribological Characteristics and Degradation Mechanism of Typical Synthetic Lubricants from Room Temperature to 300 ℃

The Mechanism of Thermal Oxidation of a Hydrotreated Naphthenic Lube Base Oil at High Temperature

Effect of iron and copper on the thermal oxidation stability of synthetic hydrocarbon aviation lubricating oil

Real-time oxidation and coking behavior of ester aviation lubricating oil in aircraft engines

Mechanism of High Stability of Water-in-Oil Emulsions at High Temperature

Thermal Oxidation Mechanism of Polyalphaolefin Greases with Lithium Soap and Diurea Thickeners: Effects of the Thickener

Effect of temperature on oxidation kinetics of EAEP soybean oil

Study on the relationship between high temperature oxidation and temperature rise rate of engine oil

Effect of Temperature on Rheological Behaviors and Tribological Properties of Nano-silica Greases Prepared from Base Oils with Different Viscosities

Research for the degradation of in - Service automotive engine lubricant oil

Investigating the Thermal Stability of Omega Fatty Acid-Enriched Vegetable Oils

Diester Derivatives from Chemically Modified Waste Cooking Oil As Substitute for Petroleum Based Lubricating Oils

Stability and Change in Fatty Acids Composition of Soybean, Corn, and Sunflower Oils during the Heating Process

THE APPLICATION OF DEPOSIT INHIBITOR IN AVIATION TURBINE OILS AT HIGH TEMPERATURE

Effect of accelerated oxidation conditions on the oxidative stability of soybean oil

Properties Of Water-Contaminated Lubricating Oil: Variation With Temperature And Small Water Content