Abstract:Lithium-sulfur (Li-S) battery has been regarded as a promising energy-storage system due to its high theoretical specific capacity of 1675 mAh g(-1) and low cost of raw materials. However, several challenges remain to make Li-S batteries viable, including the shuttling of soluble lithium polysulfide intermediates and pulverization of Li metal anode. Engineering stable electrode-separator interfaces without causing large mass/volume increase of inactive materials and electrolyte uptake is an effective approach to improve the cycling stability of Li-S batteries while maintaining high available energy density. Herein, we report the engineering of a stable electrode-separator interface with an ultrathin conductive polymer nanolayer on the pore walls of both surfaces of the separator via a simple and scalable approach using in-situ vapor-phase polymerization of polypyrrole (PPy) on commercial Celgard separator with only a small increase in overall mass and volume. The inherent hydrophilicity of PPy enables the separator to have enhanced electrolyte uptake, which facilitates homogenous Li+ flux and thus uniform plating and stripping of metallic lithium at the anode side during the charge/discharge processes. Meanwhile, the chemical immobilization effect of PPy suppresses the migration of the soluble polysulfides and improves the stability of the sulfur cathode. We showed that a Li parallel to Li symmetrical cell with the PPy modified separator gave a low and stable overpotential of less than 30 mV for over 250 h' stripping and plating test at 1 mA cm(-2) with a fixed areal capacity of 3 mAh cm(-2), which was significantly better than that using a regular Celgard separator. Using the PPy modified separator, Li-S cell with sulfur/carbon black composite cathode and lithium anode delivered stable cycling for 250 cycles at 0.5 C with a low capacity decay rate of 0.083% per cycle. Even for a Li-S cell with a high-areal-capacity sulfur cathode (4.8 mAh cm(-2)), good cycling stability was achieved. It gave a reversible areal capacity of 3.6 mAh cm(-2) after 150 charge/discharge cycles at 0.2 C with 75.6% capacity retention. Besides, the as-achieved separator showed better thermal stability than the bare counterpart. This work offers an alternative approach for achieving a practical Li-S battery toward high energy density and long cycle life through simple and scalable separator-electrode interface engineering without significant increase in volume and mass.

Integrating Flexible PMIA Separator and Electrode for Dealing with Multi-Aspect Issues in Li–S Batteries

Engineering Stable Electrode-Separator Interfaces with Ultrathin Conductive Polymer Layer for High-Energy-density Li-S Batteries

A Robust, Highly Stretchable Ion-Conducive Skin for Stable Lithium Metal Batteries

A flexible and conductive MXene-coated fabric integrated with <i>in situ</i> sulfur loaded MXene nanosheets for long-life rechargeable Li-S batteries

Multifunctional and Seamlessly Integrated Soft/Rigid Interphase Realizing a Stable Lithium-Metal Anode for a High-Performance Lithium-Metal Battery under a Lean Electrolyte

Integrated Thin Film Battery Design for Flexible Lithium Ion Storage: Optimizing the Compatibility of the Current Collector‐Free Electrodes

Constructing a LiPAA Interface Layer: a New Strategy to Suppress Polysulfide Migration and Facilitate Li+ Transport for High-Performance Flexible Li-S Batteries.

A viscous oligomer multifunctional separator coating to enable high specific energy lithium-sulfur battery

Manipulating Electrolyte and Solid Electrolyte Interphase to Enable Safe and Efficient Li-S Batteries

Ultrathin, Mechanically Durable, and Scalable Polymer-in-Salt Solid Electrolyte for High-Rate Lithium Metal Batteries

Designing a Multifunctional Separator for High-Performance Li-S Batteries at Elevated Temperature

Anchoring Polysulfide with Artificial Solid Electrolyte Interphase for Dendrite-Free and Low N/P Ratio Li-S Batteries

In Situ Self‐Polymerization of Thioctic Acid Enabled Interphase Engineering Towards High‐Performance Lithium–Sulfur Battery

Integrated, Flexible Lithium Metal Battery with Improved Mechanical and Electrochemical Cycling Stability

A dual-coated multifunctional separator for the high-performance lithium-sulfur batteries

An Integrate and Ultra-Flexible Solid-State Lithium Battery Enabled by in Situ Polymerized Solid Electrolyte

All‐Purpose Electrode Design of Flexible Conductive Scaffold toward High‐Performance Li–S Batteries

Separator Rich in SnF2 and NO3- Direct Ultra-Stable Interface toward High Performance Li Metal Batteries

Towards Practical Li–S Battery with Dense and Flexible Electrode Containing Lean Electrolyte

Coupling a Sponge Metal Fibers Skeleton with In Situ Surface Engineering to Achieve Advanced Electrodes for Flexible Lithium–Sulfur Batteries

In Situ Artificial Solid Electrolyte Interface Engineering on an Anode for Prolonging the Cycle Life of Lithium-Metal Batteries.