Abstract:Membrane biofouling represents a major challenge ever-present in the practical application of polyamide (PA) thin-film composite (TFC) reverse osmosis (RO) membranes. This work focused on grafting polyacrylamide (PAAm) onto PA-TFC via an in-situ atomic transfer radical polymerization (ATRP) method to improve the biofouling resistance of PA-TFC. The ATRP initiators, isobutyryl bromide (iPB), were introduced into PA matrix using a bifunctional small molecule, 2-bromoisobutyryl bromide (BIBB), added in organic hexane solutions to participate in interfacial polymerization through the condensation reaction with m-phenylenediamine. The successful introduction of iPB was confirmed by membrane surface characterizations, and the iPB density in PA layer was tuned by varying the BIBB concentrations in hexane solutions based on the variation in water permeance and salt rejections of iPB-loaded PA-TFC. The ATRP for the gradual growth of PAAm brush was thus in-situ achieved on the PA-TFC surface from the pre-incorporated iPB groups and the length of PAAm chains was facilely controlled via tuning ATRP polymerization time. The PAAm grafted PA-TFC exhibited a minimum decrement of water permeance and essentially retained salt rejections relative to the un-grafted ones. More importantly, the grafted membranes presented synergistically enhanced anti-adhesion and bacteriostatic performance towards either Gram-negative Escherichia coli (E. coli) or Gram-positive Bacillus subtilis (B. subtilis). Also, the grafted membranes presented a lower final flux decline ratio (FDRf) and higher final flux recovery ratio (FRRf) in relation with the un-grafted membranes in the dynamic bovine serum albumin (BSA) fouling test. Particularly, the membrane grafted with longer PAAm chains from extended grafting time showed better anti-biofouling performance: the sterilization ratio towards E. coli and B. subtilis achieved up to 98.8% and 99.0%, respectively, and FDRf of just 3.7% and FRRf of 97.6% after 3 × 8 h BSA fouling test for the membrane subjected to 2 h ATRP grafting. The PAAm grafting induced greater water wettability of membrane surface and the flexible chain structure of PAAm were proposed to account for the enhanced anti-adhesion and bacteriostasis towards bacteria, which collaboratively led to the improved biofouling resistance.

Anti-biofouling Nanofiltration Membrane Constructed by In-Situ Photo-Grafting Bactericidal and Hydrophilic Polymers

Hydrophilic Modified Polydopamine Tailored Heterogeneous Polyamide in Thin-Film Nanocomposite Membranes for Enhanced Separation Performance and Anti-Fouling Properties

Preparation and Characterization of an Amphiphilic Polyamide Nanofiltration Membrane with Improved Antifouling Properties by Two-Step Surface Modification Method

Achieving highly effective non-biofouling performance for polypropylene membranes modified by UV-induced surface graft polymerization of two oppositely charged monomers.

Fouling is the beginning: upcycling biopolymer-fouled substrates for fabricating high-permeance thin-film composite polyamide membranes

Engineering polyamide nanofiltration membrane with bifunctional terpolymer brushes for antifouling and antimicrobial properties

Thin-Film Composite Polyamide Membranes with in Situ Attached Ag Nanoparticles for Fouling-Mitigated Wastewater Treatment

Antifouling Nanofiltration Membrane Fabrication via Surface Assembling Light-Responsive and Regenerable Functional Layer

Incorporating Organic Nanospheres into the Polyamide Layer to Prepare Thin Film Composite Membrane with Enhanced Biocidal Activity and Chlorine Resistance

Thin-Film Composite Nanofiltration Membrane Modified by Fulvic Acid to Enhance Permeability and Antifouling Performance

Improving the biofouling resistance of polyamide thin-film composite membrane via grafting polyacrylamide brush on the surface by in-situ atomic transfer radical polymerization

A continuous porous porphyrinic polymer thin-film composite membrane for anti-biofouling and molecular sieving

Polyphenol-assisted In-Situ Assembly for Antifouling Thin-Film Composite Nanofiltration Membranes

Surface modification of NF membrane with zwitterionic polymer to improve anti-biofouling property

Fabrication of Anti-Fouling Polyamide Nanofiltration Membrane by Incorporating Streptomycin As a Novel Co-Monomer

Highly Permeable and Fouling-Resistant Polyamide Nanofiltration Membranes with Embedded Boron Nitride Nanosheets for the Purification of Water

Designing a multifunctional TFC membrane with improved permeability and anti-biofouling performance using zwitterionic, quaternary ammonium, and fluorinated materials

A Poly(vinylidene Fluoride)-Graft-poly(dopamine Acrylamide) Copolymer for Surface Functionalizable Membranes

Interface Engineering of Microporous Polypropylene Membranes for Polyamide Thin-Film Composite Nanofiltration Membranes with Robust Structure and Superior Performance

Tailored Nanofiltration Membranes with Enhanced Permeability and Antifouling Performance Towards Leachate Treatment

Preparation of highly permeable and selective nanofiltration membranes with antifouling properties by introducing the capsaicin derivative into polyamide thin selective layer by bidirectional interfacial polymerization