Abstract:Modern magnesium-based alloys are broadly used in various industries as well as for biodegradable medical implants due to their exceptional combination of light weight, strength, and plasticity. The studied ZEK100 alloy had a nominal composition of 1 wt.% zinc, 0.1 wt.% zirconium, and 0.1 wt.% rare earth metals (REMs) such as Y, Ce, Nd, and La, with the remainder being Mg. It has been observed that between the solidus (Ts = 529.5 ± 0.5 °C) and liquidus temperature (Tl = 645 ± 5 °C), the Mg/Mg grain boundaries can contain either the droplets of a melt (incomplete or partial wetting) or the continuous liquid layers separating the abutting Mg grains (complete wetting). With the temperature increasing from Ts to Tl, the transformation proceeds from incomplete to complete grain boundary wetting. Below 565 °C, all grain boundaries are partially wetted by the melt. Above 565 °C, the completely wetted Mg/Mg grain boundaries appear. Their portion grows quickly with an increasing temperature until reaching 100% at 622 °C. Above 622 °C, all the solid Mg grains are completely surrounded by the melt. After rapid solidification, the REM-rich melt forms brittle intermetallic compounds. The compression strength as well as the compression yield strength parameter σ02 strongly depend on the morphology of the grain boundary layers. If the hard and brittle intermetallic phase has the shape of separated particles (partial wetting), the overall compression strength is about 341 MPa and σ02 = 101 MPa. If the polycrystal contains the continous intergarnular layers of the brittle intermetallic phase (complete wetting), the overall compression strength drops to 247 Mpa and σ02 to 40 Mpa. We for the first time observed, therefore, that the grain boundary wetting phenomena can strongly influence the mechanical properties of a polycrystal. Therefore, grain boundary wetting can be used for tailoring the behavior of materials.

Isometric Tilt Grain Boundaries and Solute Segregation in a Deformed Mg-Zn-Ca Alloy

Exploring Solute Behavior and Texture Selection in Magnesium Alloys at the Atomistic Level

Periodic linear complexions: Co-segregation of solutes at a low-angle grain boundary in a magnesium alloy

Grain boundary segregation spectrum in basal-textured Mg alloys: From solute decoration to structural transition

Origin of twin-like { 33 6 ̄ 4 } tilt boundary and associated solute segregation in a high strain rate deformed Mg-Y alloy

Atomic-scale inhomogeneous solute distribution in an ultrahigh strength nanocrystalline Al-8 Mg aluminum alloy

Grain boundary and twin boundary solute segregations in nanocrystalline Al-Mg alloy

Solute Induced Defect Phase Transformations in Mg Grain Boundaries

Evolution of Deformation Substructure and MgxZnyCaz Metastable Phase in Fine-Grained Mg Alloys

Role of and dislocations on the room-temperature grain boundary migration in a deformed Mg alloy

Nonsymmetrical Segregation of Solutes in Periodic Misfit Dislocations Separated Tilt Grain Boundaries

Grain Boundary Wetting Transition in the Mg-Based ZEK 100 Alloy

Deformation Mechanisms of Magnesium Alloys with Rare-Earth and Zinc Additions under Plane Strain Compression

First-principles investigation of the Mg, Cu segregation at Al Σ5 (310) and Σ9 (221) symmetrical tilt grain boundaries

Effect of dynamic recrystallization, LPSO phase, and grain boundary segregation on heterogeneous bimodal microstructure in Mg-9.8Gd-3.5Y-2.0Zn-0.4Zr alloy

Hot deformation behavior of novel high-strength Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy

Crystallographic features of < 1 1 ̄ 00 > axis tilt boundaries in a high strain rate deformed Mg 9Y alloy

Quasi-in-situ observations of microstructural evolution during cyclic deformation of a Mg-Zn-Ca alloy

Orientation dependence of intracrystalline and grain boundary deformation behavior in Mg-2Y using nanoindentation and CPFEM

Effect of Cu and Mg co-segregation on the strength of the Al grain boundaries: A molecular dynamics simulation