Abstract:Modern aero and power industry needs high-performance gas turbine. Directional solidification (DS) columnar grain and single crystal (SX) blade as key parts of gas turbine serve in heavy stress and high temperature conditions. The DS and SX blade are mainly produced by high rapid solidification (HRS) method, and HRS is one of useful DS technology, which has a property that the heat dissipating ways are changing during the process and the temperature gradients will vary correspondingly. The dendrite grain arrays were the substructure of a DS or SX blade. The structure of the dendrite grain arrays influences the mechanical property of the final casting very much, but is seriously affected by the solidification parameters, such as temperature gradient. In this work, the dendrite grain growth of DD6 superalloy was studied based on cellular automaton- finite difference (CA-FD) model concerning the HRS method's macro solidification parameters. Mathematic models for dendrite grain growth controlled by temperature field and solute field were built to describe the competitive growth and morphology evolution of dendrite grains. Then the dendrite calculation model was coupled with the models of DS process calculation, and some HRS solidification parameters were included, such as withdrawal rate, pouring temperature, etc. The coupled models were used to predict the dendrite grain competitive growth of DD6 superalloy during the DS process. The variation of solute distribution and the dynamic adjustment of dendritic spacing during the process could be predicted by simulating calculation. The DS experiment was carried out with a cylinder sample, and dendrite grains' distribution in the transverse and longitude section was observed by OM and SEM. Then the simulated dendritic morphology was compared with that by experiment. The primary and secondary dendritic spacing by experiment and simulation were measured, and the compared results revealed that as the DS process going on the temperature gradient decreased gradually and the primary dendritic spacing was increasing. So simulation results of the DS dendritic competitive growth were validated by the experiment results, and the proposed models could predict the dendrite grain morphology and the adjustments of DS dendritic spacing of DD6 superalloy very well.

Numerical Simulation on the Single-Crystal Grain Structure of GH4169 Superalloy Steel in the Spiral Grain Selector Using Procast Software

Numerical Simulation on Solidification Structure of 30Cr(2)Ni(4)MoV Steel Under Different Temperature Gradient Using Procast Software

Numerical Simulation and Experimental Study on Spiral Grain Selector in Directional Solidification of Single Crystal Superalloy

Simulation And Experimental Studies On Grain Selection And Structure Design Of The Spiral Selector For Casting Single Crystal Ni-Based Superalloy

Numerical Simulation and Experimental Grain Selection of DD6 Superalloy in Spiral Grain Selector by Directional Solidification

Numerical Simulation of Grain Selection Behavior of Single Crystal Ni3al Based Superalloy Casting

Simulation and experimental studies on grain selection behavior of single crystal superalloy I. starter block

Grain Selection During Solidification in Spiral Grain Selector

Simulation of Grain Selection During Single Crystal Casting of A Ni-Base Superalloy

Numerical Simulation of Temperature Field and Grain Structure in the Solidification of K4169 Superalloy Shell Casting

Simulation of grain selection during solidification of Ni base single crystal superalloy in spiral grain selector

Numerical Simulation of Grain Growth of Directionally Solidified DZ4125 Alloy under Varied Blade Orientations

Numerical simulation of Ni-based Single Crystal Superalloy Based on ProCast

Simulation and Experimental Studies on Grain Selection Behavior of DD5 Single Crystal Superalloy

Simulation and Experimental Investigation of Grain Structure, Residual Stress,γ′ Phases in Single Crystal Blade

Simulation of stray grain formation in Ni-base single crystal turbine blades fabricated by HRS and LMC techniques

Numerical Simulation of Temperature Field and Grain Structure in Cu-10Al Alloy Produced by Heated Mould Continuous Casting

Computer simulation on the dynamic solidification process of super-alloy turbine blade

Numerical Simulation of Dendrite Grain Growth of Dd6 Superalloy During Directional Solidification Process

Numerical Simulation of Solidification Process on Single Crystal Ni-Based Superalloy Investment Castings

Progress on Modeling and Simulation of Directional Solidification of Superalloy Turbine Blade Casting