Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes ( d ̄ ) were used for two-stage tensile tests under the conditions with distinct pre-strain εpre and intersection angle θSPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing εpre and θSPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d ̄ . This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre-strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Modeling of Flow Stress Size Effect Based on Variation of Dislocation Substructure in Micro-Tension of Pure Nickel

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Modeling the Strain Rate-Dependent Constitutive Behavior in Nanotwinned Polycrystalline Metals

Modelling the Plastic Deformation of Nanostructured Metals with Bimodal Grain Size Distribution

Micromechanical modeling for mechanical properties of gradient-nanotwinned metals with a composite microstructure

MODELLING THE YIELD STRENGTH AND DUCTILITY IN COMPOSITE NANOTWINNED COPPER

Size dependence of flow stress and plastic behaviour in microforming of polycrystalline metallic materials

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

Modelling of ultra-thin steel sheet in two-stage tensile deformation considering strain path change and grain size effect and application in multi-stage microforming

Modeling of material deformation behavior in micro-forming under consideration of individual grain heterogeneity

Numerical Simulation of Microstamping Process to Fabricate Multi-channel of SUS304 Thin Sheets with Consideration of Grain Structures

A microscale constitutive model for thin stainless steel sheets considering size effect

Simulating Size and Volume Fraction-Dependent Strength and Ductility of Nanotwinned Composite Copper

A constitutive model on flow stress prediction from the contribution of twin and grain refinement, strain and strain rate during surface mechanical attrition treatment of metals

Microstructure-Based Modeling of Deformation in Steels Based on Constitutive Relationships from Micropillar Compression

Constitutive Modeling of Annealed OFHC with Wide Strain-Rate and Temperature Effects: Incorporating Dislocation Dynamics and Normalized Microstructural Size Evolution

Microstructure-Based Multiscale Modeling of Deformation in MarBN Steel under Uniaxial Tension: Experiments and Finite Element Simulations

Size Effect in Stainless Steel Thin Wires under Tension

Multiscale Analysis And Numerical Modeling Of The Portevin-Le Chatelier Effect

Crystal plasticity modelling of multi-stage deformation of ultra-thin sheets considering grain size effect and strain path change

Experiment and modeling based studies of the mesoscaled deformation and forming limit of Cu/Ni clad foils using a newly developed damage model