Abstract:The effect of large pre-deformation on the microstructural evolution and mechanical property anisotropy of large-sized Al-Zn-Mg alloy extruded profiles with thin-walls and high-ribs was investigated. The increase in pre-deformation reduces the time required for the alloy to reach peak hardness during aging at 120 °C, but leads to a decrease in peak hardness. The undeformed alloy exhibits the highest ultimate tensile strength (UTS) of 527 MPa and yield strength (YS) of 497 MPa in the 90° direction, accompanied by a low elongation (EL) of 12.7 %, highlighting significant anisotropy. At a large pre-deformation of 38 %, UTS, YS, and EL dramatically fall, with IPA values of 2.43 %, 3.77 %, and 11.96 %, respectively. Increased pre-deformation promotes the formation of substructures without altering the texture type, which remains predominantly A 1 * and A 2 * textures, but reduces texture intensity. After aging treatment, the primary intragranular precipitates are η' phases, and dislocations generated by pre-deformation stimulate the heterogeneous nucleation of η' phases and their transformation to η phases. Additionally, increased pre-deformation leads to the growth and uneven distribution of precipitates and an increase in the width of the precipitate-free zones (PFZ). The reduced anisotropy is attributed to decreased texture intensity, increased dislocation substructures, higher η phase content, and expanded PFZ width. Pre-deformation between 8 % and 18 % effectively maintains mechanical properties while reducing anisotropy. These findings provide insights into optimizing pre-deformation treatments to balance mechanical properties and anisotropy in Al-Zn-Mg alloy profiles.

Effect of pre-strain levels and high temperature annealing on the formability of AZ31 Mg alloy thin sheet during stretch deformation

Effect of Stretch Bending on the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy

Influence of In-Plane Simple Shear Strain on the Grain Orientation Regulation and Stretch Formability of Pre-twinned AZ31 Magnesium Alloy Sheet

Improvement of stretch formability and weakening the basal texture of Mg alloy by corrugated wide limit alignment and annealing process

Deformation Behavior and Microstructure Evolution of AZ31 Mg Alloy by Forging–Bending Repeated Deformation with Multi-pass Lowered Temperature

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Strain Rate and Temperature Effects on Formability and Microstructure of AZ31B Magnesium Alloy Sheet

Effect of Rolling Parameters on Room-Temperature Stretch Formability of Mg–2Zn–0.5Ca Alloy

Effect of large pre-deformation on the microstructure, texture and mechanical properties of Al-Zn-Mg alloy extruded profiles

Influence of Microstructure and Mechanical Properties on Formability in High Strain Rate Rolled AZ31 Magnesium Alloy Sheets

Preferential grain growth and textural evolution of AZ31B Mg alloy during annealing after isothermal compression at 400 °C

Effect of Pre-Stretch on the Precipitation Behavior and the Mechanical Properties of 2219 Al Alloy

Effect of Final Rolling Speed on Microstructure and Performance of AZ31 Magnesium Alloy Sheet under Small Strain Condition

Exceptional improvement in the yield strength of AZ61 magnesium alloy via cryo-stretching and its implications on the grain growth during annealing

Effect of pre-stretching on enhancing yield strength of as-extruded Mg-Sm-Ce based alloy

Effect of 90° route on microstructure of AZ31 magnesium alloy sheets by forging-bending repeated deformation

Unveiling the planar deformation mechanisms for improved formability in pre-twinned AZ31 Mg alloy sheet at warm temperature

Effect of Pass Strain on the Microstructure, Texture and Mechanical Properties of AZ31 Magnesium Alloy Fabricated by High Strain Rate Multiple Forging

Significantly improvement in formability and ductility of AZ31 Mg alloy by differential temperature rolling

Strengthening Mechanism of Room Temperature Mechanical Properties for AZ31 Magnesium Alloy by Continuous Variable Cross section Direct Extrusion

Plastic deformation of AZ31B magnesium alloy in the preform and electropulsing treatment process