Abstract:Selective Laser Melting (SLM) has significant advantages in manufacturing complex structural components and refining the alloy microstructure; however, spatter, as a phenomenon that accompanies the entire SLM forming process, is prone to problems such as inclusions, porosity, and low powder recovery quality. In this paper, a Computational Fluid Dynamics–Discrete Particle Method (CFD–DPM) simulation flow for predicting the SLM spatter behavior is established based on the open-source code OpenFOAM. Among them, the single-phase flow Navier–Stokes equation is used in the Eulerian framework to equivalently describe the effect of metal vapor and protective gas on the flow field of the forming cavity, and the DPM method is used in the Lagrangian framework to describe the metal particle motion, and the factors affecting the particle motion include particle–particle collision, particle–wall collision, fluid drag force, gravity, buoyancy force, and additional mass force. In addition, the equivalent volume force and fluid drag force are used to characterize the fluid–particle coupling interaction. For the spatter behavior and powder bed denudation phenomenon, the calculation results show that the spatter height and the drop location show a clear correlation, and the powder bed denudation phenomenon is caused by the high-speed gas flow, causing the surrounding gas to gather in the forming area, which in turn drives the motion of the powder bed particles. For the effect of powder layer thickness on spatter and powder bed denudation, the calculation results show that the effect of powder layer thickness on the number of spatters is large (when the thickness was increased from 50 μm to 100 μm, the number of spatters increased by 157%), but the effect on spatter height and drop location distribution is small. When the powder layer thickness is small, the width of the denudation zone is significantly larger, but when the powder layer reaches a certain thickness, the width of the denudation zone does not show significant changes. It should be noted that the presented model has not been directly validated by experiments so far due to the difficulty of tracking the large-scale motion of SLM spatter in real time by current experimental means.

Mechanisms and Characteristics of Spatter Generation in Slm Processing and Its Effect on the Properties

Investigation into spatter behavior during selective laser melting of AISI 316L stainless steel powder

Effect of Spatter Behavior on Mechanical Properties and Surface Roughness of Printed Parts during PBF-LM of 316L

Effects of the processing parameters on the forming quality of stainless steel parts by Selective Laser Melting

Types of spatter and their features and formation mechanisms in laser powder bed fusion additive manufacturing process

Coupling Analysis on Microstructure and Residual Stress in Selective Laser Melting (SLM) with Varying Key Process Parameters

Study on the Technique During Selective Laser Melting of Stainless Steel Powder

Bulk-Explosion-Induced Metal Spattering During Laser Processing

Experimental and computational study on thermal and fluid behaviours of powder layer during selective laser melting additive manufacturing

Formation Mechanism of Spatter and Its Influence on Mechanical Properties in Process of Laser Powder Bed Fusion

Research Progress on Spatter Behavior in Laser Powder Bed Fusion

A Study on the Residual Stress During Selective Laser Melting (SLM) of Metallic Powder

Effect of Molten Pool Boundaries on the Mechanical Properties of Selective Laser Melting Parts

Adhesion Effects on Spreading of Metal Powders in Selective Laser Melting

CFD–DPM Simulation Study of the Effect of Powder Layer Thickness on the SLM Spatter Behavior

A Review of Spatter in Laser Powder Bed Fusion Additive Manufacturing: In Situ Detection, Generation, Effects, and Countermeasures

The Investigation of Plume and Spatter Signatures on Melted States in Selective Laser Melting

Densification Behavior of Gas and Water Atomized 316l Stainless Steel Powder During Selective Laser Melting

Mesoscale Modelling of Selective Laser Melting: Thermal Fluid Dynamics and Microstructural Evolution

Influence of Spatter Particles Contamination on Densification Behavior and Tensile Properties of CoCrW Manufactured by Selective Laser Melting

Balling Phenomenon in Selective Laser Melting Process