Abstract:Ti-6Al-4V parts are usually hypothesized as isotropic mechanical properties during micro-machining operation. However, the crystal anisotropic mechanical property is an influential factor in the machining of crystals with different sizes and orientations. The hypothesis causes distinct variation in predicting machining force, and consequently the surface integrity cannot be exactly predicted in the micro-machining. Actually, Ti-6Al-4V parts are pseudo isotropy composed of grains with different orientations, elastic modulus, and hardness. Simultaneously, the initiation mode of plastic slip system varies with the grain orientation when the crystal is subjected to an applied load. It is challengeable to evaluate the effect of crystal orientation on its macroscopic properties, either by traditional experimental methods or macroscopic finite element analysis. Nano-indentation provides one novel method to investigate the plastic deformation of selected grains with specific orientations to characterize their mechanical response properties. This research aims to investigate the plastic behavior of α phase Ti-6Al-4V with different orientation grains by means of nano-indentation experiment and crystal plastic finite element method. In the study, single crystals of α phase are classified into “hard grains” (θ < 30°), “soft grains” (θ > 60°) and “normal grains” (30° < θ < 60°) by defining the crystal inclination angle (θ). The elastic modulus and hardness of hard grains are 9% and 28% larger than those of soft grains, respectively. This difference in mechanical properties depends on the slip system that dominates the plastic deformation behavior. The plastic deformation of soft grains is dominated by prismatic slip (48%), while hard grains are accommodated to plastic deformation by basal slip (51%). The average total cumulative shear strain of the soft grains is double that of the hard grains at a maximum load of 10 mN. Meanwhile, the sensitivity analysis is performed to evaluate the effects of the three sets of < a > slip systems and the two sets of < c + a > slip systems on plastic deformation with different grain orientations. The research contributes to the understanding of the plastic deformation mechanism in micro-machining and the exactly predicting the surface integrity generated from micro-machining.

Experimental Study and Crystal Plasticity Finite Element Simulations of Nano-Indentation-induced Lattice Rotation and the Underlying Mechanism in TC6 Single Α-Grain

Numerical and Experimental Studies of Deep Indentation on Single Crystals

Experiments and Crystal Plasticity Finite Element Simulations of Nanoindentation on Ti–6Al–4V Alloy

Effect of Crystallographic Orientation on Nano-indentation Behavior of Nickel Based Single Crystal Super Alloys

Anisotropic Plasticity of Nanocrystalline Ti:A Molecular Dynamics Simulation

Investigation on the Crystal Plasticity of Α Phase Ti-6Al-4V Based on Nano-Indentation Simulation and Experiment

Experiments and crystal plasticity simulations for the deformation behavior of nanoindentation: Application to the 2 phase of TiAl alloy

Experiments and crystal plasticity simulations for the deformation behavior of nanoindentation: Application to the α2 phase of TiAl alloy

Unveiling the Local Deformation Behavior of Typical Microstructures of Nickel-Based Single Crystals under Nanoindentation

Atomistic Simulation of Nanoindentation on Incipient Plasticity and Dislocation Evolution in Γ/γ′ Phase with Interface and Void

Influnence of Indenter on the Nanoindentation of Ni Based Single Crystal Alloy

Characterization of Grain Boundary Deformation Processes in Commercial Purity Titanium Using Nanoindentation and Crystal Plasticity Modeling

Experimental and Simulation Analysis of Residual Topography Dominated Deformation Mechanism of Nanoindentation: a Case Study of Inconel 625 Superalloy

High Strain Gradient Plasticity Associated with Wedge Indentation into Face-Centered Cubic Single Crystals: Geometrically Necessary Dislocation Densities

Indentation Pileup Behavior of Ti-6Al-4V Alloy: Experiments and Nonlocal Crystal Plasticity Finite Element Simulations

Mechanical Characterization and Strain-Rate Sensitivity Measurement of Ti-7333 Alloy Based on Nanoindentation and Crystal Plasticity Modeling

Microstructure Evolution-Dominated Mechanical Properties of Pure Titanium under Nanoindentation

Deformation Behaviour and 6H-LPSO Structure Formation at Nanoindentation in Lamellar High Nb Containing TiAl Alloy

The Influence of Crystallographic Orientation and Grain Boundary on Nanoindentation Behavior of Inconel 718 Superalloy Based on Crystal Plasticity Theory

Effects of Crystalline Anisotropy and Indenter Size on Nanoindentation by Multiscale Simulation.

Atomistic simulation of nanoindentation response of dual-phase nanocrystalline CoCrFeMnNi high-entropy alloy