Abstract:Aluminium silicon carbide (AlSiC) composites are silicon carbide (SiC) ceramic-reinforced aluminium matrix composites. When wide band-gap semiconductors, typically silicon carbide (SiC) and gallium nitride (GaN), work at high power density and high operating temperature, AlSiC is usually used as the thermal management material to dissipate a large amount of heat accumulated in the devices, thus reducing equipment failures caused by thermal runaway. Wetting is an important property to be considered because it can affect the heat transfer performance of AlSiC. The purpose of this work was to study the influence of 3 C-SiC crystalline orientation on the wetting behaviour of molten aluminum droplets through molecular dynamics simulation. The density distribution of Al droplets obtained on the (110) plane was stratified, while on the (111) plane, a relatively dense spindle region appeared. The physical quantities associated with the wettability of aluminium droplets on the (110) and (111) planes were also analysed. The contact angles on these two crystal planes obtained after fitting were 84.3° and 95.3°, respectively. The droplet exhibits a wetting state on the (110) plane while presenting characteristics between wetting and hydrophobicity on the (111) plane. The magnitude of the interface energy fluctuation of the (110) system was between − 17 kJ/mol and − 27 kJ/mol which was less than that of the (111) system. In the time step 2.85 × 10 5 fs before and after fitting, the average self-diffusion coefficients of aluminium droplets in the (111) system increased by 2.29 × 10 −8 and 1.9 × 10 −7 m 2 /s compared with those in the (110) system. Although it was more difficult for molten aluminium to diffuse on the (110) plane, it took longer time for the (111) system to reach stability. This further showed that the role of the 3 C-SiC crystalline orientation on droplet wettability cannot be ignored. Therefore, understanding the influence of crystal orientation on the wetting characteristics of AlSiC during its preparation is helpful for improving its heat transfer performance, and to ensure the reliable operation of wide band-gap semiconductor devices.

Effect of Temperature on Wetting Kinetics in Al/SiC System: a Molecular Dynamic Investigation

Sonoprocessing of wetting of SiC by liquid Al: A thermodynamic and kinetic study

Wetting and Interfacial Behavior of Molten Al on Mo-Ni(Co)-Si Coated SiC Ceramic

Role of Si in the wetting of TiC by Al

Study of the 3C-SiC surface crystalline orientation effect on the wettability of molten aluminium droplets by molecular dynamics simulation

Wetting and Spreading Behavior of Sn–Ti Alloys on SiC

Effect of substrate temperature on adhesion at liquid-aluminum/silica interface by phantom wall method

Wettability At Al-Mg/Cerarnic Interfaces

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Tribological Behavior of Liquid Phase Sintered SiC Ceramics Under Dry Condition

Wetting Kinetics of a Hypo-Eutectic Al–Si System

Wetting Behaviors of Nickel-Based Alloys on Sintered Silicon Carbide Ceramics

Wettability And Its Improvement At Ai/Sic Interfaces

Effect of temperature on rheological behavior of silicon carbide aqueous suspension

Molecular dynamics simulation of the temperature effect on ideal mechanical properties of SiC/BN interface for SiCf/SiC composites

Laser-induced dynamic wetting behavior and interfacial evolution of AlSi5 alloy on Ti6Al4V alloy

Wetting behavior of Al on the surface of SiC textured by nanosecond laser

Effect of Cr content on the wetting behavior of Cu–Cr/SiC system

Molecular dynamics study of high temperature wetting kinetics for Al/NiAl and Al/Ni3Al systems: Effects of grain boundaries

Study on the oxidation mechanism of Al-SiC composite at elevated temperature

Si Diffusion Across the Liquid/solid Interface of Capillary Driven (Al–si)-Kxalyfz Micro-Layers