Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. During the welding process of thick plates, it is difficult to evaluate the residual stress distribution in thick welds accurately because complicated residual stress is generated by multi-thermal cycles. In this study, a multi-pass butt joint was fabricated using Q690 high strength steel with the thickness of 75 mm, meanwhile experiments were carried out to characterize the microstructure and measure the through-thickness distribution of longitudinal residual stress in a butt-welded joint by the contour method. Then numerical methods were developed to predict the through-thickness distribution of residual stress in butt-welded joints. To evaluate residual stress accurately and efficiently, the effects of solid-state phase transformation (SSPT) and initial stress were taken into consideration, and the parallel computation technology and iterative substructure method were employed. The root-mean-square error (RMSE) was employed to evaluated the prediction accuracy of numerical methods between measurement and numerical results of residual stress. Through comparing the simulated results with experimental data, the validity of the developed numerical methods was verified. Numerical results indicate that the through-thickness distribution of residual stress in butt-welded joints is very complex and peak value of tensile stress can be found in the area adjacent to the heat-affected zone (HAZ). Moreover, the RMSE is significantly decreased from 307 to 8 when considering the effect of SSPT on residual stress in weld vicinity, and the RMSE is apparently decreased from 137 to 11 when considering the effect of initial stress on residual stress in base metal.

Influence of Lumping Passes on Calculation Accuracy and Efficiency of Welding Residual Stress of Thick-Plate Butt Joint in Boiling Water Reactor

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Influences of lumped passes on welding residual stress of a thick-walled nuclear rotor steel pipe by multipass narrow gap welding

Influence of Material Model on Prediction Accuracy of Welding Residual Stress in an Austenitic Stainless Steel Multi-pass Butt-Welded Joint

Accurate evaluation on residual stress considering solid-state phase transformation and initial stress in thick weld

Sensitivity Analysis of Some High Efficiency Computational Methods for Welding Process Numerical Simulation

Numerical Simulation Of Temperature Field And Residual Stress In Multi-Pass Welds In 2.25cr-1mo-0.25v Steel Plate And Comparison With Experimental Measurements

Numerical simulation of residual stress before and after post-weld heat treatment in butt-welded pipes with dissimilar steel

Finite Element Modeling of Residual Stress in Welded Joint ofThick-Walled 316LN Stainless Steel Pipes

3-D Finite Element Analysis of Welding Residual Stress for Half-Pipe Jacket Made of 304 Stainless Steel

Three Dimension Simulation Analysis of the Interpass Stress and Deformation During Multipass Welding

Predicting Welding Residual Stress of a Multi-pass P92 Steel Butt-Welded Joint with Consideration of Phase Transformation and Tempering Effect

Investigation of Residual Stress in Butt-Welded Plates Considering Phase Transformation

Welding Numerical Simulation Analysis of AP 1000 Insert Plate and Penetration Sleeves Based on ABAQUS

Numerical investigation on residual stress distribution and evolution during multipass narrow gap welding of thick-walled stainless steel pipes

Numerical Simulation of Residual Stresses on Butt-Weld of Thick Steel Plate

Welding residual stress analysis of the X80 pipeline: simulation and validation

Analysis on calculation accuracy and efficiency of multi-pass butt weld of pipe

Numerical Simulation of Temperature Evolution, Solid Phase Transformation, and Residual Stress Distribution during Multi-Pass Welding Process of EH36 Marine Steel

Numerical simulation of three-dimension stress field in double-sided double arc multipass welding process