Abstract:New Phosphine‐oxides as Type I photoinitiators. 3D printing is the technology of choice for the rapid production of objects with complex morphologies and controlled physical and chemical properties. 3D printing by photopolymerization is of great interest because of its ability to access very small scales and its high resolution. In the case of recent 3D printers, the preferred wavelength for light irradiation is 405 nm since it is a safe and energy‐economical irradiation. For 3D printing to be effective, it is therefore necessary to develop easily accessible, stable and highly efficient photoinitiating systems at the 405 nm wavelength. Beside, with the increasing use of photoinitiators, it is essential to develop structures with low cytotoxicity. Hence, the development of new photoinitiators is currently of major interest. To this end, the photochemical properties (triplet energy, bond dissociation energy, cleavage reaction enthalpy, and absorption properties) of several molecules have been calculated by molecular modeling and the most promising compounds have been synthesized. In this paper, four phosphine oxides photoinitiators (ADPO‐1, CPO‐2, CPO‐3, and FPO‐1) are synthesized and characterized. Subsequently, their absorption properties are measured and their efficiencies in photopolymerization under LED irradiation at 405 nm are evaluated. It is important to note that these structures have never been reported in 3D printing. Markedly, among the obtained photoinitiators, two of them show better efficiency than the commercially available and widely used phenylbis(2,4,6‐trimethylbenzoyl)phosphine oxide (BAPO) in photopolymerization (i.e., (Rp/[M0]) x100 values are 6.94, 12.95, and 4.93 s−1 for CPO‐2, ADPO‐1, and BAPO; with [M0] the initial acrylate function concentration). Furthermore, one of the synthesized photoinitiators is successfully used in 3D printing of thermoplastics for potential recycling ability. Finally, one of the obtained structures shows a lower cytotoxicity than the benchmark structure diphenyl(2,4,6‐trimethylbenzoyl)phosphine oxide (TPO).

Conjugated Bifunctional Carbazole-Based Oxime Esters: Efficient and Versatile Photoinitiators for 3D Printing under One- and Two-Photon Excitation

Efficient 3D Printing Via Photooxidation of Ketocoumarin Based Photopolymerization

Study on the photoinitiation mechanism of carbazole-based oxime esters (OXEs) as novel photoinitiators for free radical photopolymerization under near UV/visible-light irradiation exposure and the application of 3D printing

Photoinitiation behavior of phenothiazines containing two oxime ester functionalities (OXEs) in free radical photopolymerization and 3D printing application

Triphenylamine-substituted BODIPY dye based photoinitiators for free radical and cationic photopolymerization under visible LED irradiation and application in 3D printing

Bisbenzothieno[b]-fused BODIPYs in panchromatic photoinitiating for the free radical and cationic photopolymerization and application in 3D printing

Novel di-2-thienyl ketone derivatives photoinitiators enable fast visible light polymerization and 3D printing

Naphthoquinone-imidazolyl derivatives-based oxime esters as photoinitiators for blue LED-induced free radical photopolymerization

Enhanced One/Two‐Photon Initiating Performance of Nitro‐Carbazole‐Styrene Based Oxime/Ketoxime Esters

Triphenylamine based oxime ester photoinitiator for LED-induced free radical photopolymerization and 3D printing

Photoinitiation Mechanisms of Novel Phenothiazine‐Based Oxime and Oxime Esters Acting as Visible Light Sensitive Type I and Multicomponent Photoinitiators

Towards safe phosphine oxides photoinitiators with good cytocompatibility for 3D printing of thermoplastics

Effect of Decarboxylation on the Photoinitiation Behavior of Nitrocarbazole-Based Oxime Esters

Visible Light Photoinitiator for 3D-Printing of Tough Methacrylate Resins

A General Strategy for Sustainable 3D Printing Based on A Multifunctional Photoinitiator

Photoinitiating Ability of Pyrene‐Chalcone‐based Oxime Esters with Different Substituents

The three-component photoinitiating systems based on flavonol sulfonate and application in 3D printing

Synthesis of Carbazole-Chalcone Bis-Oxime Esters (CCBOEs) as Blue Light Photoinitiators of Polymerization

A high performance phenyl-free LED photoinitiator for cationic or hybrid photopolymerization and its application in LED cationic 3D printing

Water-soluble bis-chalcone-based photoinitiators with long-wavelength absorption for radical polymerization and 3D printing

Phenothiazine Derivative-Based Photoinitiators for Ultrafast Sunlight-Induced Free Radical Polymerization and Rapid Precision 3D Printing