Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Computational Studies of CL‐20‐based Materials

Molecular Dynamics Simulations of Mechanical Properties of Epoxy-Amine: Cross-linker Type and Degree of Conversion Effects

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Computational Study of the Nanoscale Mechanical Properties of C-S-H Composites under Different Temperatures

Thermal and Crystalline Properties of Random Copolymer of CL and DTC Prepared by La(OAr)3

Molecular dynamics simulation of bilayer core-shell structure of CL-20 surface-modified by polydopamine coated with polymer binder

First principles molecular dynamics simulation and thermal decomposition kinetics study of CL-20

A MD Simulation and Experimental Study

Molecular Dynamics Simulation of Effect of Carbon Nanotube Diameter on Properties of Crosslinked Epichlorohydrin Rubbers

A Molecular Dynamics Simulation Study on Enhancement of Mechanical and Tribological Properties of Nitrile—Butadiene Rubber with Varied Contents of Acrylonitrile

Toughening modification of cellulose acetate butyrate and using for CL-20-based polymer bonded explosives

Quantitatively predicting the mechanical behavior of elastomers via fully atomistic molecular dynamics simulation

Full-Atomistic Optimized Potentials for Liquid Simulations and Polymer Consistent Force Field Models for Biocompatible Shape-Memory Poly(ε-caprolactone)

Theoretical investigations on CL-20/ANTA co-crystal explosive via molecular dynamics method

Solid‐Solid Phase Transformation Behavior of ε‐CL‐20 Induced by Typical Organic Solvents: A Theoretical and Experimental Study

Molecular-Level Insight of CP52/NBR Damping Composites through a Combination of Molecular Dynamics Simulation and Experimental Method

Design a Cross-Linked Film Based on Cellulose Nanocrystals Doping for Enhancing the Interfacial Performance and Desensitization of CL-20

Molecular dynamics simulation of CL20/DNDAP cocrystal-based PBXs

Effect of triethylene glycol bis(3‐tert‐butyl‐4‐hydroxy‐5‐methylphenyl)propionate on structure and mechanical properties of nitrile butadiene rubber/clay nanocomposites

Precisely tailoring the thermodynamic compatibility between single-walled carbon nanotubes and styrene butadiene rubber via fully atomistic molecular dynamics simulation and theoretical approach

CL-20-Based Cocrystal Energetic Materials: Simulation, Preparation and Performance