Abstract:In order to investigate the effect of TiB2 contents on the microstructure and wear resistance of titanium matrix composites, commercial pure Ti (CP-Ti) powders with 0–7.5 wt.% TiB2 particles were melted by selective laser melting (SLM) to produce the in-situ Ti-TiB composites. When the TiB2 content increases from 2.5 wt.% to 7.5 wt.%, the microstructures of the Ti-TiB composites undergo a transition from the single phase of α′-Ti to the mixed phases of α′-Ti, TiB and TiB2, and the acicular α′-Ti is refined significantly from 1.03 ± 0.24 μm to 0.36 ± 0.05 μm, showing that increasing the TiB2 content induces the formation of TiB and refines the microstructure. Moreover, large TiB2 particles are not melted completely and they react with the Ti matrix liquid to form a TiB layer around the Ti matrix during SLM. However, small TiB2 particles are completely dissolved into the Ti matrix liquid so that the eutectic TiB grains are precipitated at the boundaries of the Ti matrix after in-situ reaction of TiB2 with Ti. The formation of α′ martensite in the titanium matrix and the addition of TiB2 can induce the fine grain strengthening, the dispersion strengthening, the solid solution strengthening in the SLM-produced composites. The results indicate that the microhardness of the composites increases from 258 ± 10.3 HV0.2 to 435 ± 14.7 HV0.2. The wear process of the SLM-produced CP-Ti and TiB2 reinforced Ti matrix composites is accompanied by adhesion wear, abrasive wear and oxidation wear. As a result, when the TiB2 content increases to 7.5%, the wear resistance of the composites increases by 32.6% compared with that of the CP-Ti. These improvements are mainly due to strengthening and hardening effects induced by TiB2 particles and refinement of Ti matrix. This study provides some basis for developing wear-resistant and high-strength titanium alloys.

Effects of rare earth elements on the microstructure and wear properties of TiB2 reinforced aluminum matrix composite coatings: Experiments and first principles calculations

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Effects of TiB2 Particles on Microstructure and Mechanical Properties of an In-Situ TiB2-Al–Cu–Li Matrix Composite

Investigation on Microstructures and Mechanical Behavior of In-Situ Synthesized TiC and TiB Reinforced Ti6Al4V Based Composite

In-situ TiB2-TiC reinforced Fe-Al composite coating on 6061 aluminum alloy by laser surface modification

Tribological properties and microstructures of Al2O3-TiC-TiB2 reinforced composites

The Effect of Micron-Sized TiB2 Particles on the Properties of Al6061 Strengthened with 4% TiB2 Nano-TiB2

Investigation on microstructural characterization of in situ TiB/Al metal matrix composite by laser cladding

Effect of different rare earths on microstructures and tensile strength of in situ hybrid reinforced (TiB2p + TiBw)/Cu composites

Effects of in-situ TiB<sub>2</sub> particles on machinability and surface integrity in milling of TiB<sub>2</sub>/2024 and TiB<sub>2</sub>/7075 Al composites

Effects of Mg, Si and multiple rare earth addition on microstructures of Al 3Ti /A356 composites

Microstructure and Tribological Behavior of in Situ Synthesized (tib+tic)/ti6al4v (tib/tic=1/1) Composites

Effects of alloy elements (Mg, Zn) on the microstructure and mechanical properties of (TiC+TiB2)/Al composites

Microstructure and compressive properties of in situ synthesized (TiB + TiC)/Ti composites

Refined microstructure and enhanced wear resistance of titanium matrix composites produced by selective laser melting

Microstructure and mechanical properties of TiB2-reinforced 7075 aluminum matrix composites fabricated by laser melting deposition

Wear Behavior of In-Situ TiC Particles Reinforced Aluminum Matrix Composite

Effects of Mg, Si and Multiple Rare Earth Addition on Microstructures of Al<sub>3</sub>Ti /A356 Composites

Microstructure and Properties of In-Situ Synthesized (ti3al + TiB)/Ti Composites by Laser Cladding

Influence of the friction and wear performance of TiB2/7075 aluminum-based composite materials prepared by friction stir processing

Effects of Microalloying and Ceramic Particulates on Mechanical Properties of Tial-Based Alloys