Abstract:The carbon-fiber-reinforced polymer (CFRP) bending structure is widely used in aviation. The emergence and spread of delamination damage will decrease the safety of in-service bending structures. Lamb waves can effectively identify delamination damage as a high-damage-sensitivity detection tool. For this present study, the signal difference coefficient (SDC) was introduced to quantify delamination damage and evaluate the sensitivity of A0-mode and S0-mode Lamb waves to delamination damage. The simulation results show that compared with the S0-mode Lamb wave, the A0-mode Lamb wave exhibits higher delamination damage sensitivity. The delamination damage can be quantified based on the strong correlation between the SDC and the delamination damage size. The control effect of the linear array PZT phase time-delay method on the Lamb wave mode was investigated by simulation. The phase time-delay method realizes the generation of a single-mode Lamb wave, which can separately excite the A0-mode and S0-mode Lamb wave to identify delamination damage of different sizes. The A0-mode Lamb wave was excited by the developed one-dimensional miniaturized linear comb transducer (LCT), which was used to conduct the detection experiment on the CFRP bending plate with delamination damage sizes of Φ6.0 mm, Φ10.0 mm, and Φ15.0 mm. The experimental results verify the correctness of the simulation. According to the Hermite interpolation results of the finite-element simulation data, the relationship between the delamination damage size and the SDC was fitted by the Gaussian function and Rational function, which can accurately quantify the delamination damage. The absolute error of the delamination damage quantification with Gaussian and Rational fitting expression does not exceed 0.8 mm and 0.7 mm, and the percentage error is not more than 8% and 7%. The detection and signal processing methods employed in the present research are easy to operate and implement, and accurate delamination damage quantification results have been obtained.

OPTIMAL EXCITATION FREQUENCY FOR DELAMINATION IDENTIFICATION OF LAMINATED BEAMS USING A0 LAMB MODE

An Algorithm Based on Logarithm of Wavenumber Amplitude for Detection of Delamination in Carbon Fiber Composite

Identifying Delamination in Carbon Fiber Composites Based on Defect Modes in Imperfect Phononic Crystals

Delamination Analysis of Carbon Fiber/Epoxy Composite Laminates under Different Loading Rates Using Acoustic Emission

Concise Analysis of Wave Propagation Using the Spectral Element Method and Identification of Delamination in CF/EP Composite Beams

Non-Destructive Evaluation of a Delamination in Laminates by Lamb Wave Propagation

Delamination assessment of a laminated composite beam using distributed piezoelectric sensor/actuator

Delamination detection on composite laminates using the modal displacement unevenness coefficient

Detection of Delamination using Laser-generated Lamb waves with Improved Wavenumber Analysis

A New Quantitative Acoustic Emission Model for Damage Characterization of Composite Laminates Using Original Waveforms

Delamination detection in laminated composite beams using electro-mechanical impedance signatures

A two-step method for delamination detection in composite laminates using experience-based learning algorithm

Predicting delamination in composite laminates through semi-analytical dynamic analysis and vibration-based quantitative assessment

A Quantitative Damage Identification Method for Cf/Ep Composite Laminates Based on Lamb Waves

Quantitative Identification of Delamination at Different Interfaces Using Guided Wave Signals in Composite Laminates

Lamb wave-based quantitative identification of delamination in CF/EP composite structures using artificial neural algorithm

Delamination prediction in composite beams with built-in piezoelectric devices using modal analysis and neural network

Delamination detection in composite laminates using improved surrogate-assisted optimization

NUMERICAL ANALYSIS FOR DETECTION OF DELAMINAION IN LAMINATES BY PIEZOELECTRIC SENSORS

A guided wave propagation method for delamination detection in fiber-metal laminates

Research on Delamination Damage Quantification Detection of CFRP Bending Plate Based on Lamb Wave Mode Control