Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Transform of Work Function of Poor-solvent Induced Active Layer Surface in All-polymer Solar Cells

Authigenic Buffer Layer: Tuning Surface Work Function in All Polymer Blend Solar Cells

Improving Active Layer Morphology of All-Polymer Solar Cells by Dissolving the Two Polymers Individually

Solvent-Activated Transformation of Polymer Configurations for Advancing the Interfacial Reliability of Perovskite Photovoltaics

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Rational design of conjugated side chains for high-performance all-polymer solar cells

MORPHOLOGIES AND PERFORMANCE OF ORGANIC SOLAR CELLS USING LOW POLYMERIZATION DEGREE ALTERNATING COPOLYMER

Optimization of active layer for efficient binary organic solar cells

Efficiency Enhancement for Bulk Heterojunction Photovoltaic Cells Via Incorporation of Alcohol Soluble Conjugated Polymer Interlayer

Modulating the nanoscale morphology on carboxylate-pyrazine containing terpolymer toward 17.8% efficiency organic solar cells with enhanced thermal stability

Alkali Salt-Doped Highly Transparent and Thickness-Insensitive Electron-Transport Layer for High-Performance Polymer Solar Cell

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

Effective Regulation of Morphologies and Exciton‐Generation Process Enables Quasi‐Planar All‐Polymer Organic Solar Cells Exceed 18% Efficiency

Boosting the Efficiency of Non-fullerene Organic Solar Cells via a Simple Cathode Modification Method

Enhanced Performance of P3HT-based Non-Fullerene Polymer Solar Cells by Optimizing Film Morphology Using Non-Halogenated Solvent

Volatilizable Solid Additive‐Assisted Treatment Enables Organic Solar Cells with Efficiency over 18.8% and Fill Factor Exceeding 80%

High Performance All-Polymer Solar Cells by Synergistic Effects of Fine-Tuned Crystallinity and Solvent Annealing.

Simultaneous Enhancement of Open‐Circuit Voltage, Short‐Circuit Current Density, and Fill Factor in Polymer Solar Cells

Improvement in Polymer Solar Cell Performance and Eliminating Light Soaking Effect Via UV-light Treatment on Conjugated Polyelectrolyte Interlayer

Improved Charge Transport and Reduced Carrier Recombination of Nonfullerene Organic Solar Cells with the Binary Solvent

High-performance hybrid perovskite solar cells with polythiophene as hole-transporting layer via electrochemical polymerization